• July 16, 2019, 10:07:00 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Bug - Plugs turns itself off after a few days of being "on"  (Read 4076 times)

MrWhite

  • Level 1 Member
  • *
  • Posts: 4

Pretty simple bug,  I have 2 of these and both of them exhibit this problem.  After a day or so of continuously being on (sometimes after a few hours), the plug cuts power.  The green LED on the front still indicates as though it is switched on (the "switched on" LED, not the WiFi connected LED).  I haven't set any schedules and the power limit is "off".  Both running the 1.02b5 firmware (latest).

Super annoying.
« Last Edit: June 11, 2014, 12:13:36 AM by MrWhite »
Logged

JavaLawyer

  • BETA Tester
  • Level 15 Member
  • *
  • Posts: 12190
  • D-Link Global Forum Moderator
    • FoundFootageCritic
Re: Bug - Plugs turns itself off after a few days of being "on"
« Reply #1 on: June 11, 2014, 06:00:56 AM »

I will forward this issue to D-Link for review and post back if I learn anything.  :-\  ???
Logged
Find answers here: D-Link ShareCenter FAQ I D-Link Network Camera FAQ
There's no such thing as too many backups FFC

MrWhite

  • Level 1 Member
  • *
  • Posts: 4
Re: Bug - Plugs turns itself off after a few days of being "on"
« Reply #2 on: February 20, 2015, 10:30:33 AM »

So this issue seems to still happen to me on the 1.10 firmware.  It's gotten much better though and seems to happen after a few months of leaving the plug in "on" mode, but for example this morning I woke up and the temperature of my aquarium was 30degreesC because the plug had turned itself off.
Logged

FurryNutz

  • Poweruser
  • ††▲
    ▲†▲
  • *****
  • Posts: 47564
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Bug - Plugs turns itself off after a few days of being "on"
« Reply #3 on: February 20, 2015, 10:40:00 AM »

Just curious, was is the power requirements of the aquarium devices? I presume a water pump and heater?
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting

MrWhite

  • Level 1 Member
  • *
  • Posts: 4
Re: Bug - Plugs turns itself off after a few days of being "on"
« Reply #4 on: February 20, 2015, 02:27:36 PM »

Chillers so about 800W total power.
Logged

FurryNutz

  • Poweruser
  • ††▲
    ▲†▲
  • *****
  • Posts: 47564
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Bug - Plugs turns itself off after a few days of being "on"
« Reply #5 on: February 21, 2015, 03:43:04 PM »

Ok, checking. Do the Chiller AMP draw more than 15amps by chance?

These are rated at Up to 1800W / 15Amps
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting

fockers

  • Level 1 Member
  • *
  • Posts: 1
Re: Bug - Plugs turns itself off after a few days of being "on"
« Reply #6 on: June 22, 2015, 12:06:25 AM »

I have a same problem with my device too. It is cut the power without any reason.
I podded two tickets to the support about this issue without any answer. It is not very professional from DLink side.  >:(
The firmware is 2.03(latest). The load is less than 13A. No schedule, no thermal protection, consumption matter is off and I donít have any rule. DSP-W215 seems to be a very good device but D-Link have to work a lot on it: some simple web interface, some simple log, even I canít check the real time clock in the device is it correct.
Logged

FurryNutz

  • Poweruser
  • ††▲
    ▲†▲
  • *****
  • Posts: 47564
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Bug - Plugs turns itself off after a few days of being "on"
« Reply #7 on: June 22, 2015, 07:24:22 AM »

We find that phone contact has better immediate results over using email.
Let us know how it goes please.

I have a same problem with my device too. It is cut the power without any reason.
I podded two tickets to the support about this issue without any answer. It is not very professional from DLink side.  >:(
The firmware is 2.03(latest). The load is less than 13A. No schedule, no thermal protection, consumption matter is off and I donít have any rule. DSP-W215 seems to be a very good device but D-Link have to work a lot on it: some simple web interface, some simple log, even I canít check the real time clock in the device is it correct.
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting