• December 02, 2020, 03:55:32 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Pages: [1] 2

Author Topic: 895L ver solid white light  (Read 993 times)

llFawkes17ll

  • Level 1 Member
  • *
  • Posts: 7
895L ver solid white light
« on: August 19, 2020, 01:39:35 PM »

Does anyone know what a solid white power light means? The router does not boot up. Tried connecting a serial connection but nothing shows up on putty. I am assuming the connection from left to right is RX (the one with a small triangle) space vcc ground TX. The anyone have any ideas?
Logged

Mr.Mom

  • Technical Engineer
  • Level 2 Member
  • *
  • Posts: 26
Re: 895L ver solid white light
« Reply #1 on: August 19, 2020, 02:02:36 PM »

White power light means there is sold power but next to it is the Internet LED should be white as well so you have internet access. See users manual at http://legacyfiles.us.dlink.com/DIR-895L/REVA/
Logged

llFawkes17ll

  • Level 1 Member
  • *
  • Posts: 7
Re: 895L ver solid white light
« Reply #2 on: August 19, 2020, 02:05:21 PM »

White power light means there is sold power but next to it is the Internet LED should be white as well so you have internet access. See users manual at http://legacyfiles.us.dlink.com/DIR-895L/REVA/

Only light that's on is the solid white power light. No other light is on.
Logged

Mr.Mom

  • Technical Engineer
  • Level 2 Member
  • *
  • Posts: 26
Re: 895L ver solid white light
« Reply #3 on: August 19, 2020, 02:06:18 PM »

Do you have a modem connected to the WAN port of the router with Ethernet cable?
Logged

llFawkes17ll

  • Level 1 Member
  • *
  • Posts: 7
Re: 895L ver solid white light
« Reply #4 on: August 19, 2020, 02:45:09 PM »

Do you have a modem connected to the WAN port of the router with Ethernet cable?
At the moment no, as I have another router connected to the modem because the 895L was malfunctioning. When it started malfunctioning it would only shows the solid white light. During boot up it wouldn't show a blicking orange light as it should but instead it only shows a solid white power light.
Logged

Mr.Mom

  • Technical Engineer
  • Level 2 Member
  • *
  • Posts: 26
Re: 895L ver solid white light
« Reply #5 on: August 19, 2020, 02:55:21 PM »

Have you tested out the WAN/Internet port with a computer to see if it connects and the computer Ethernet NIC card shows any speeds. PS it just for physical connection not a way to log in or anything else.
Logged

llFawkes17ll

  • Level 1 Member
  • *
  • Posts: 7
Re: 895L ver solid white light
« Reply #6 on: August 19, 2020, 02:58:03 PM »

Have you tested out the WAN/Internet port with a computer to see if it connects and the computer Ethernet NIC card shows any speeds. PS it just for physical connection not a way to log in or anything else.

I just did and under the internet properties it shows 1.0 Gbps. I also tried bringing up the crash recovery option by using Firefox with 192.168.0.1 but that does not bring up the loading screen.
« Last Edit: August 19, 2020, 03:01:08 PM by llFawkes17ll »
Logged

Mr.Mom

  • Technical Engineer
  • Level 2 Member
  • *
  • Posts: 26
Re: 895L ver solid white light
« Reply #7 on: August 19, 2020, 03:09:40 PM »

Could be a bad router and since its legacy product might be time to replace it.
Logged

llFawkes17ll

  • Level 1 Member
  • *
  • Posts: 7
Re: 895L ver solid white light
« Reply #8 on: August 19, 2020, 03:13:52 PM »

Could be a bad router and since its legacy product might be time to replace it.
Any reason why the serial connection wouldn't even show up on a putty session? Are you able to tell me what the correct RX TX grn order is on the JP1 port?
Logged

Mr.Mom

  • Technical Engineer
  • Level 2 Member
  • *
  • Posts: 26
Re: 895L ver solid white light
« Reply #9 on: August 19, 2020, 03:52:03 PM »

Might not be able to putty into the router, you might want to check datasheet or users manual for more information about this discontinued Router.
Logged

GreenBay42

  • Administrator
  • Level 11 Member
  • *
  • Posts: 2590
Re: 895L ver solid white light
« Reply #10 on: August 20, 2020, 06:07:51 AM »

Try crash recovery. Turn the router off, hold in the reset button and turn it on. Continue holding for 15 seconds and release. After boot up, go to 192.168.0.1 and a firmware screen should appear. Load the latest firmware. If it does not work, try 2-3 times. If it still will not work, router is dead.

Note you will have to statically assign your computer (192.168.0.2 / 255.255.255.0).
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49375
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: 895L ver solid white light
« Reply #11 on: August 20, 2020, 07:56:25 AM »

Logged
Cable: 1Gb/50Mb>NetGear CAX80>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

llFawkes17ll

  • Level 1 Member
  • *
  • Posts: 7
Re: 895L ver solid white light
« Reply #12 on: August 20, 2020, 08:37:59 AM »

Try crash recovery. Turn the router off, hold in the reset button and turn it on. Continue holding for 15 seconds and release. After boot up, go to 192.168.0.1 and a firmware screen should appear. Load the latest firmware. If it does not work, try 2-3 times. If it still will not work, router is dead.

Note you will have to statically assign your computer (192.168.0.2 / 255.255.255.0).

Tried that but the power light never turns orange. From the moment I turn it on the power light remains white.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49375
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: 895L ver solid white light
« Reply #13 on: August 20, 2020, 08:55:44 AM »

You mighty try searching and or asking someone over in the DD-WRT forum about JTAG port information. I know that some of those users dive deeper into routers and router HW, one may have the port configuration information you need to check on the boot loader and nvram. Some like to fiddle around with that over there. If you can get into this then if you have the means, you might be able to recover the router. If not then the router is just bad and needs replacing. Either the NVRAM is corrupt or there is a HW failure. If you want another 895L you might find a used one on places like Amazon or fleabay.  ::)
Logged
Cable: 1Gb/50Mb>NetGear CAX80>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

llFawkes17ll

  • Level 1 Member
  • *
  • Posts: 7
Re: 895L ver solid white light
« Reply #14 on: August 20, 2020, 09:22:03 AM »

You mighty try searching and or asking someone over in the DD-WRT forum about JTAG port information. I know that some of those users dive deeper into routers and router HW, one may have the port configuration information you need to check on the boot loader and nvram. Some like to fiddle around with that over there. If you can get into this then if you have the means, you might be able to recover the router. If not then the router is just bad and needs replacing. Either the NVRAM is corrupt or there is a HW failure. If you want another 895L you might find a used one on places like Amazon or fleabay.  ::)

Thank you. It's weird that putty won't even show any information. That's a first for me.
Logged
Pages: [1] 2