• October 31, 2024, 04:52:54 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: DIR-615 T1 WiFi strength becomes low, need to restart every few hours  (Read 3938 times)

lulzintosh

  • Level 1 Member
  • *
  • Posts: 3

Hello,

I have a DIR-615 T1, been using it for about an year with WiFi to about 4 devices and 1 wired connection.

The WiFi signal strength becomes really low as the hours go by, to the point where I get just 1 MBPS in literally the next room where the router is located.
Literally 1 wall and a 5 meters away I get 1 MBPS download speed.

I restart the router and BAM, 20 MBPS download speed. But after 2 - 3 hours, it goes down to 1 MBPS again.


How do I resolve this issue?
I have tried resetting the device multiple times.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DIR-615 T1 WiFi strength becomes low, need to restart every few hours
« Reply #1 on: January 21, 2019, 09:49:28 AM »

Link>Welcome!

  • Link>What Firmware version is currently loaded? Found on the routers web page under status.
  • What region are you located?
  • Are you wired or wireless connected to the router?
  • Has a Factory Reset been performed?



Internet Service Provider and Modem Configurations
  • What ISP Service do you have? Cable or DSL?
  • What ISP Modem Mfr. and model # do you have?

Wireless Configurations
Links>Wireless Installation Considerations and Managing Signal Congestion and Good Neighbour Policy
  • Ensure the default (dlink) SSID name is changed. Ensure that different SSID names are used between each WiFi 2.4/5Ghz radios. Can be anything and not something that's already in use by any neighbouring WiFi routers. Under Setup/Wireless/Manual.
  • What wireless modes are you using?
  • 2.4Ghz Routers only: Try single mode G or N or mixed G and N?
  • Channel Width set for Auto 20/40Mhz or try 20Mhz only.
  • Try setting a manual Channel to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear. 13 for EU regions.
  • What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES, so you might want to try TPIK only or Auto TPIK and AES.
  • What wireless devices do you have connected?
  • Ensure any devices with WiFi adapter drivers are updated.
  • Any 2.4Ghz or 5Ghz cordless house phones or WiFi APs near by that maybe causing interferences?
  • Any other WiFi routers in the area that maybe causing interferences? Link> Use a WiFi Scanner to find out. How many?
  • If you have any of these options, Try turning OFF or ON Short GI, WLAN Partition, Extra Wireless Protection and HT 20/40 Co-existence if you have it. Also testing with HT20/40Mhz Co-existence enabled will impact results as well. I prefer to use this option OFF. Recommended settings are default. Under Advanced/Advanced Wireless.

Router Placement
Forum User - "Well I feel really dumb. After moving the router away from other electronic devices my speeds are back to normal. Just a heads up for anyone experiencing slow speeds, you might want to move it away from other electronics and see if that helps."
3-6' feet minimum safe distance between devices.
Placement on main level floor and central in the building and WELL ventilated is preferred. Not in basements or closets as building materials, or near by electronics devices could interfere or hinder good signal propagation.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.