• September 20, 2019, 12:54:10 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: How to enable communication of devices from different VLANs  (Read 1226 times)

yaylitzis

  • Level 1 Member
  • *
  • Posts: 3
How to enable communication of devices from different VLANs
« on: September 18, 2018, 02:25:00 AM »

In my router (DSR-1000AC with Firmware 3.11_WW), I created a new VLAN 192.168.3.x following the instructions from HOW to Setup Two VLANS ‑ DSR‑Series.

I used a simple switch (not managed) and I connected it to port 4 of the router. Then, I connected a PC to this switch and it took successfully an IP from the new VLAN, the 192.168.3.2.

Till here all good. However, this PC can't see the devices from the default VLAN 192.168.0.x (e.g. a network disk). The ping doesn't return anything..

The above guide notes that:

InterVLAN Routing can stay “Off” this way there is no way that both networks will see each other

So I turned in ON that setting. However, the devices from the 2 subnets can't "talk" each other. So my question is how can enable that?
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47761
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: How to enable communication of devices from different VLANs
« Reply #1 on: September 18, 2018, 08:16:46 AM »

Link>Welcome!

  • What Hardware version is your router? Look at sticker under the router case.
  • Link>What Firmware version is currently loaded? Found on the routers web page under status.
  • What region are you located?

Are you sure the setting was enabled and saved and applied?
You might need to reboot the router, switch and PCs after making the change.

I recommend that you phone contact your regional D-Link support office and ask for help and information regarding this.
Link> Tech Support Contact Information
We find that phone contact has better immediate results over using email.
Let us know how it goes please.
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting

yaylitzis

  • Level 1 Member
  • *
  • Posts: 3
Re: How to enable communication of devices from different VLANs
« Reply #2 on: September 19, 2018, 05:44:57 AM »

Fortunately, I figured out what I had missed to do...
I hadn't enabled that option in the default VLAN too.. I did it, restarted the router as you wrote and then my devices were view-able!

Thanks a lot!
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47761
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: How to enable communication of devices from different VLANs (RESOLVED)
« Reply #3 on: September 19, 2018, 07:04:54 AM »

Glad you figured it out. Thanks for letting us know. Enjoy.  ;)
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting