Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[FurryNutz]

Ya, it's a one off and I didn't catch it. I presume just something that slipped by and wasn't really thought of or may have bee noticed.  I think we just presumed that reservation behavior wasn't an issue in this regard after disconnecting a device and not being able to see the reservation it left behind.  It's a new UI and i'm sure a few things may have appeared. There was an issue in reserving IP addresses out of the gate which as been fixed. I'm sure this will be fixed. Its not a show stopper.

[KentM]

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!


Are you joking....are you guys NEW? How the hell was this option omitted! I'm sitting here in my office where I am setting up a new PC. The old one died so it is no longer an option to reconnect it and delete the reserved IP. There are many processes over the network which rely on a static IP.......BUT I CAN'T SET THE IP BECAUSE THE UI IS MISSING THE OPTION TO REMOVE RESERVED IPs. At the very least when an IP conflict is detected there should be an option to replace the device.

[FurryNutz]

Link>Welcome!

• Link>What Firmware version is currently loaded? Found on the routers web page under status.
• What region are you located?

D-Link is aware of the problem and is working on it..
For now, do not set any reservations on the router for your devices. You can set static IP addresses ON the devices out side of the routers  DHCP  IP address pool which will help avoid conflict in IP addressing until this is fixed.
I recommend factory resetting the router and then set up the router again, just don't set any IP reservations.

Please refrain from using profane language here in the forums!!!

Thank you.

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!


Are you joking....are you guys NEW? How the hell was this option omitted! I'm sitting here in my office where I am setting up a new PC. The old one died so it is no longer an option to reconnect it and delete the reserved IP. There are many processes over the network which rely on a static IP.......BUT I CAN'T SET THE IP BECAUSE THE UI IS MISSING THE OPTION TO REMOVE RESERVED IPs. At the very least when an IP conflict is detected there should be an option to replace the device.

[KentM]

Fortunately I had saved the MAC address of the old NIC in a text file. I was able to just Change the NIC MAC of the new computer to that of the old one. I was then able to remove the IP reserved to that MAC address.

[FurryNutz]

Link>What Firmware version is currently loaded? Found on the routers web page under status.
What region are you located?

Glad you were able to get the reservation re-configured. D-Link is aware of this and is working on it as most users would not normally have this kind of work around available to them and is not recommended to change the MAC addresses on devices.

We hope the next FW release will have this fix.

 

[KentM]

Firmware: v1.02
Location: US

[FurryNutz]

Thank you for the info. We look forward to the next FW release. Please be patient. 

Firmware: v1.02
Location: US

[S0Z]

Thank you for the info. We look forward to the next FW release. Please be patient. 

Firmware: v1.02
Location: US

Same problem
Rev B1
Fw 2.03
EU
Same problem

Anybody try to ddwrt on this model? And how to revert back if I don't like it?

[FurryNutz]

There isn't a Rev B version of the 880L.

Can you confirm the router model and Rev version please?

Thank you for the info. We look forward to the next FW release. Please be patient. 

Firmware: v1.02
Location: US

Same problem
Rev B1
Fw 2.03
EU
Same problem

Anybody try to ddwrt on this model? And how to revert back if I don't like it?

[S0Z]

There isn't a Rev B version of the 880L.

Can you confirm the router model and Rev version please?

Thank you for the info. We look forward to the next FW release. Please be patient. 

Firmware: v1.02
Location: US

Same problem
Rev B1
Fw 2.03
EU
Same problem

Anybody try to ddwrt on this model? And how to revert back if I don't like it?

Sorry I forget to write a model 860L. But problem is the same. After I set up static IP address and remove device I can't setup the same address without reset the router.

[FurryNutz]

v2.03 is the last release version and hasn't been anything since.

I recommend that you phone contact your regional D-Link support office and ask for help and information regarding this. We find that phone contact has better immediate results over using email.

Let us know how it goes please.

There isn't a Rev B version of the 880L.

Can you confirm the router model and Rev version please?

Thank you for the info. We look forward to the next FW release. Please be patient. 

Firmware: v1.02
Location: US

Same problem
Rev B1
Fw 2.03
EU
Same problem

Anybody try to ddwrt on this model? And how to revert back if I don't like it?

860L

[S0Z]

v2.03 is the last release version and hasn't been anything since.

I recommend that you phone contact your regional D-Link support office and ask for help and information regarding this. We find that phone contact has better immediate results over using email.

Let us know how it goes please.

Local support know less than me. Thy only know hot to exchange device for the new one...but problem stays the same.

There isn't a Rev B version of the 880L.

Can you confirm the router model and Rev version please?

Thank you for the info. We look forward to the next FW release. Please be patient. 

Firmware: v1.02
Location: US

Same problem
Rev B1
Fw 2.03
EU
Same problem

Anybody try to ddwrt on this model? And how to revert back if I don't like it?

860L

[FurryNutz]

You could try DDWRT if they support it. You'll need to check with them to see if it's supported. If so then I would review there support site for help and information on installation. They will have all information regarding installation and going back to OEM FW. OpenWRT is also supported on the 860L Rev B I believe.
You can use this as well to revert back to OEM FW should you not like WRT:
Emergency Recovery Mode

This board is for the 880L. Please post over on the DIR-860L for your future needs regarding OEM FW issues:
http://forums.dlink.com/index.php?board=393.0

Thank you.