• December 05, 2019, 11:34:20 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: DIR-827 + DAP-1522  (Read 2607 times)

lardio

  • Level 1 Member
  • *
  • Posts: 2
DIR-827 + DAP-1522
« on: June 07, 2013, 03:35:04 PM »

I  have connected an DAP-1522 in bridge mode to my DIR-827 to connect my home theater and ps3 and its work fine. But i cant no more connect my iPhone on the wifi.. its normal ?
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47953
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DIR-827 + DAP-1522
« Reply #1 on: June 10, 2013, 06:43:53 AM »

Link>Welcome!
  • What Hardware version is your router? Look at sticker under router.
  • Link>What Firmware version is currently loaded? Found on routers web page under status.
  • What region are you located?

Router and Wired Configurations
Some things to try: - Log into the routers web page at 192.168.0.1. Use IE, Opera or FF to manage the router.
  • Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting.
  • Ensure devices are set to auto obtain an IP address.
  • If IPv6 is an option on the router, select Local Connection Only or Disable IPv6 options under Setup/IPv6.
  • Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall.
  • Enable uPnP and Multi-cast Streaming under Advanced/Networking. Disable uPnP for testing Port Forwarding rules. Enable IPv6 Multi-cast Streaming for routers that have a Media Server option. Disable IPv6 Multi-cast Streaming if IPv6 or Media Server is not being used.
  • Turn off WISH, and WPS under Advanced.
  • WAN Port Speed set to Auto or specific speed? Some newer ISP modems support 1000Mb so manually setting to Gb speeds can be supported by the router. Advanced/Advanced Networking/WAN Port Speed
  • Set current Time Zone, Date and Time. Use an NTP Server feature. Tools/Time.


 
Wireless Configurations
Links>Wireless Installation Considerations and Managing Signal Congestion
  • Ensure the default (dlink) SSID name is changed. Can be anything and not something thats already in use by any neighboring WiFi routers. Under Setup/Wireless/Manual.
  • What wireless modes are you using?
  • 2.4Ghz and 5Ghz routers: Try single mode G or N or mixed G and N on 2.4Ghz and single mode N on 5Ghz?
  • Channel Width set for Auto 20/40Mhz or try 20Mhz only.
  • Try setting a manual Channel to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear.
  • What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES, so you might want to try TPIK only or Auto TPIK and AES.
  • What wireless devices do you have connected?
  • Try turning off Short GI, WLAN Partition,and Extra Wireless Protection if you have it. Under Advanced/Advanced Wireless.
  • Enable WMM Enable Under Advanced/Advanced Wireless.
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting