• November 30, 2020, 04:02:15 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Pages: [1] 2

Author Topic: Port forwarding or application rule doesn't work  (Read 48447 times)

zum0

  • Level 1 Member
  • *
  • Posts: 13
Port forwarding or application rule doesn't work
« on: March 09, 2012, 07:00:48 PM »

I have a D-link DIR-855 with Hardware Version: A2 & Firmware Version: 1.22NA.

I can't make any port forward or application rule for any of my computers on the network.

The only method is to put the computer on DMZ and that is a bad solution in this case.

If I check the log in the router I can only see blocked incoming TCP  connection...

In this case I tried to connect via ssh from another internet connection in to my home computer behind the router.

Code: [Select]
[INFO] Sat Mar 10 03:57:05 2012 Blocked incoming TCP connection request from xxx.xxx.xxx.x:11823 to xxx.xxx.xxx.xxx:22
Any ideas?

Was it a bad choice to use 1.22NA fw?

Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49371
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Port forwarding or application rule doesn't work
« Reply #1 on: March 10, 2012, 10:04:29 AM »

What ISP Service do you have? Cable or DSL?
What ISP Modem do you have? Stand Alone or built in router?
What ISP Modem make and model do you have?
If this modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems.
To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged.

Some things to try:
Turn off ALL QoS or Disable Traffic Shaping (DIR only) GameFuel (DGL only and if ON.) options. Advanced/QoS or Gamefuel.
Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual.
Turn on DNS Relay under Setup/Networking.
Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking
Ensure devices are set to auto obtain an IP address.
Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall.

Enable uPnP and Multi-cast Streaming under Advanced/Networking.
Logged
Cable: 1Gb/50Mb>NetGear CAX80>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49371
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Port forwarding or application rule doesn't work
« Reply #2 on: March 12, 2012, 09:04:36 AM »

Any status on this? Hope something has helped.  ;)
Logged
Cable: 1Gb/50Mb>NetGear CAX80>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

alien

  • Level 3 Member
  • ***
  • Posts: 207
Re: Port forwarding or application rule doesn't work
« Reply #3 on: March 12, 2012, 09:05:25 AM »

its well known problem according Dlink Ru.

Look at ftp://ftp.dlink.ru/pub/Router/DIR-855/Firmware/
Logged
First Router Draytek Vigor 2310N for performance an VPN

Backup routers Dlink Dir855, DIR 655
Backup router ASUS WL500GP Premium en WL500g with DDWRT.

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49371
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Port forwarding or application rule doesn't work
« Reply #4 on: March 12, 2012, 09:11:39 AM »

He's got a NA unit not a EU or RU unit. There different FWs.
Logged
Cable: 1Gb/50Mb>NetGear CAX80>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

zum0

  • Level 1 Member
  • *
  • Posts: 13
Re: Port forwarding or application rule doesn't work
« Reply #5 on: March 13, 2012, 05:15:05 AM »

What ISP Service do you have? Cable or DSL?
What ISP Modem do you have? Stand Alone or built in router?
What ISP Modem make and model do you have?
If this modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems.
To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged.

Some things to try:
Turn off ALL QoS or Disable Traffic Shaping (DIR only) GameFuel (DGL only and if ON.) options. Advanced/QoS or Gamefuel.
Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual.
Turn on DNS Relay under Setup/Networking.
Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking
Ensure devices are set to auto obtain an IP address.
Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall.

Enable uPnP and Multi-cast Streaming under Advanced/Networking.

Cable. No modem.

Cat5 directly to the router.

Have fixed all those settings but still the same problem.

I think it's because my firmware and I can't downgrade/upgrade the fw atm. :(

He's got a NA unit not a EU or RU unit. There different FWs.

It's a EU unit so the fw I did use probably messed up the router...
« Last Edit: March 13, 2012, 05:16:55 AM by zum0 »
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49371
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Port forwarding or application rule doesn't work
« Reply #6 on: March 13, 2012, 07:15:27 AM »

What region are you located?

Ya if you use NA on a EU unit then it's not going to work correctly. Need to get back to EU FW.

Also use CAT6 cables. Cat5 will probably not be the preferred cable to use.
Logged
Cable: 1Gb/50Mb>NetGear CAX80>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

zum0

  • Level 1 Member
  • *
  • Posts: 13
Re: Port forwarding or application rule doesn't work
« Reply #7 on: March 13, 2012, 07:58:02 AM »

What region are you located?

Ya if you use NA on a EU unit then it's not going to work correctly. Need to get back to EU FW.

Also use CAT6 cables. Cat5 will probably not be the preferred cable to use.

Northern EU.

I have tried to get back to EU FW but it doesn't work.

Tried with factory reset & update the device with 1.23wwb01 fw over cable but it doesn't work.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49371
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Port forwarding or application rule doesn't work
« Reply #8 on: March 13, 2012, 08:03:16 AM »

Supposed you could try the Recovery method in the FW update sticky in this forum maybe  :-\
Logged
Cable: 1Gb/50Mb>NetGear CAX80>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

zum0

  • Level 1 Member
  • *
  • Posts: 13
Re: Port forwarding or application rule doesn't work
« Reply #9 on: March 15, 2012, 03:32:12 AM »

Supposed you could try the Recovery method in the FW update sticky in this forum maybe  :-\

Is it this Sticky you mean? http://forums.dlink.com/index.php?topic=42448.0 I have tried that. :'(
Logged

alien

  • Level 3 Member
  • ***
  • Posts: 207
Re: Port forwarding or application rule doesn't work
« Reply #10 on: March 15, 2012, 06:22:38 AM »

if you want to roll back to european version got to dlink germany: ftp://ftp.dlink.de/dir/dir-855/driver_software/
Get recovery from Na firmware. Then you can load the eu or ww firmware.
Logged
First Router Draytek Vigor 2310N for performance an VPN

Backup routers Dlink Dir855, DIR 655
Backup router ASUS WL500GP Premium en WL500g with DDWRT.

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49371
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Port forwarding or application rule doesn't work
« Reply #11 on: March 15, 2012, 07:13:29 AM »

If FW doesn't seem to want to load on this unit I would contact D-Link for an RMA.
Keep us posted.
Logged
Cable: 1Gb/50Mb>NetGear CAX80>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

zum0

  • Level 1 Member
  • *
  • Posts: 13
Re: Port forwarding or application rule doesn't work
« Reply #12 on: March 15, 2012, 11:06:03 AM »

if you want to roll back to european version got to dlink germany: ftp://ftp.dlink.de/dir/dir-855/driver_software/
Get recovery from Na firmware. Then you can load the eu or ww firmware.


Awesome. I'll try that and post the result.
Logged

zum0

  • Level 1 Member
  • *
  • Posts: 13
Re: Port forwarding or application rule doesn't work
« Reply #13 on: March 15, 2012, 11:57:39 AM »

Perfect!!

I now have Firmware Version: 1.23WW.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49371
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Port forwarding or application rule doesn't work
« Reply #14 on: March 15, 2012, 12:11:37 PM »

Kewl. Hope it works well for you.
Enjoy.
Logged
Cable: 1Gb/50Mb>NetGear CAX80>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.
Pages: [1] 2