• November 21, 2018, 08:52:11 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: DCS-2530L - Firmware v1.04.01 Released  (Read 1893 times)

GreenBay42

  • Administrator
  • Level 8 Member
  • *
  • Posts: 1496
DCS-2530L - Firmware v1.04.01 Released
« on: June 01, 2018, 07:59:35 AM »

Firmware version 1.04.01 released. This is the official KRACK release.

Firmware - ftp://FTP2.DLINK.COM/PRODUCTS/DCS-2530L/REVA/DCS-2530L_REVA_FIRMWARE_v1.04.01.zip


Release Notes:

New Features:
1. Support Google casting
2. Add FTP selection item on the Event

Fixed:
1. Fixed D-Track bug HQ20171113000007 Event cannot send after system reboot
2. Fixed D-Track bug HQ20171017000008 DCS-2530L cannot use mydlink lite to setup Motion Detection default(30%).
3. Fixed D-Track FW v1.3.3beta WPA and direct mode abnormal.
4. Fixed mydlink Motion block mapping issue for iOS app
5. Fixed WPA2 security issue (KRACK)
6. Fixed D-Track but HQ20170719000003 for recording file abnormal if set 1 frame per seconds on profile2

Logged

Reddok

  • Level 1 Member
  • *
  • Posts: 19
Re: DCS-2530L - Firmware v1.04.01 Released
« Reply #1 on: June 12, 2018, 02:09:07 PM »

This firmware release appears to have done something to the sensitivity of the motion detection.  Getting constant false triggers now.  Whenever the light changes just the slightest amount it triggers a motion alert.  Dropping the sensitivity in the app has no effect.  The firmware was the only change made.  Anyone else seeing this?  Seems to be a recurrent theme with d-link that they have trouble ignoring scene intensity changes.

Also, why can't motion alerts be disabled when the camera switches between day and night mode?
Logged

GreenBay42

  • Administrator
  • Level 8 Member
  • *
  • Posts: 1496
Re: DCS-2530L - Firmware v1.04.01 Released
« Reply #2 on: June 12, 2018, 02:52:17 PM »

I will report this to a tech.
Logged

Reddok

  • Level 1 Member
  • *
  • Posts: 19
Re: DCS-2530L - Firmware v1.04.01 Released
« Reply #3 on: June 20, 2018, 01:12:33 PM »

Any updates on this?  This latest firmware is completely unusable for motion detection.  Sensitivity at 1% and the slightest movement or light intensity change triggers motion.  Sensitivity at 0% and no triggers at all.  Also the mydlink app re-defaults the sensitivity to 30% every time it is enabled or disabled.
Logged

GreenBay42

  • Administrator
  • Level 8 Member
  • *
  • Posts: 1496
Re: DCS-2530L - Firmware v1.04.01 Released
« Reply #4 on: June 20, 2018, 01:42:29 PM »

I will check for you. I haven't heard anything back from the tech or headquarters.
Logged

Reddok

  • Level 1 Member
  • *
  • Posts: 19
Re: DCS-2530L - Firmware v1.04.01 Released
« Reply #5 on: June 28, 2018, 12:42:06 PM »

Over two weeks and no responses.  Searching just reveals a ton of other threads with people having similar issues with lighting intensity changes triggering motion detection on various dlink cameras with no solutions.  This has rendered this camera completely useless for security - I'm receiving several false alerts per minute today as the clouds drift by (Camera is in a room with closed curtains and not pointed at the windows - but it still doesn't matter). 

I'm going to have to toss this camera out and go with a competitor that has been able to figure out how to ignore scene intensity changes (just about anyone else).
Logged

GreenBay42

  • Administrator
  • Level 8 Member
  • *
  • Posts: 1496
Re: DCS-2530L - Firmware v1.04.01 Released
« Reply #6 on: June 28, 2018, 03:25:42 PM »

Really sorry for the delay.

If you downgrade the firmware does it go back to "normal"?

How much area do you have selected in the motion detection setup? Try less selected "boxes" and see if it improves.

Please contact tech support to get it in the system.  http://support.dlink.ca/search.aspx

Also with a lot of home cameras motion detection is triggered by pixel-change so light changes and shadows will cause it to trigger. But you having it at 1% and still triggers that much is ridiculous and it definitely should not be working that way.

UPDATE: The tech tested with the latest firmware and didn't see much change in the motion detection.  It worked the same as the previous version.  Try resetting the camera and setup. Possibly the upgrade glitched something. Again very sorry for the delay.
« Last Edit: June 28, 2018, 03:32:42 PM by GreenBay42 »
Logged

Reddok

  • Level 1 Member
  • *
  • Posts: 19
Re: DCS-2530L - Firmware v1.04.01 Released
« Reply #7 on: June 28, 2018, 07:30:18 PM »

Performed a factory reset on the camera.  Now I am unable to reconnect to the camera using the app.  An average user would be out of luck at this point.  I can log in to the default wifi and default ip address and set up the wifi, but the camera will not not re-add to mydlink.  Pretty horrible experience. 
Logged

Doctor Doom

  • Level 3 Member
  • ***
  • Posts: 125
Re: DCS-2530L - Firmware v1.04.01 Released
« Reply #8 on: July 03, 2018, 08:59:33 AM »

I have also tested the motion detection mechanism using firmware 1.02 as a baseline and 1.04 and using the same motion detection area and sensitivity (set at 85% in an indoor environment with natural sunlight close by), I do not see a noticeable change in behavior with regards to triggering.

You may need to contact support to investigate further. 
Logged

JJdaCool

  • Level 1 Member
  • *
  • Posts: 22
  • I be the JJdaCool
Re: DCS-2530L - Firmware v1.04.01 Released
« Reply #9 on: August 02, 2018, 01:02:04 PM »


Well, this camera continues to have glitches as of August.02.2018
Yeah the motion is alerting about every 5 to 10 minutes randomly for me.
Usually caused by a cloud or angle of sunlight or the ir shutter switching or neighborhood ac voltage level change of plus or minus 0.05 volts (like if the neighbor's cooler turns on.)
0 to 29 percent is lots of alerts, 30 to 46 is a few less, 47 to 100 is same as 0 to 29.

Still wont reboot if after system crash, have to unplug and plug back in, though it does seem to crash less with the 1.04.01 update.
Wifi "seems" somewhat better or more stable with 1.04.01 update.
The time to live view in the apps for this camera still takes about 10 to 20 seconds at least to load.

Video quality is good after loading time.

I have tried downgrading the firmware to 1.03 and 1.01, the number of alerts is a tiny fewer but not much, but the previous firmwares have a lot of other problems though that make it difficult to set motion and percentage correctly at all.

This is my general observations of this camera, it is NOT a full log of every glitch I have experienced with the 2530L.
Logged
Yo!

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 46161
  • D-Link Global Forum Moderator
    • New DIR-890L Router with SmartConnect™ Technology
Re: DCS-2530L - Firmware v1.04.01 Released
« Reply #10 on: August 02, 2018, 01:50:34 PM »

I recommend that you phone contact your regional D-Link support office and ask for help and information regarding this. Ask for an RMA.
Link> Tech Support Contact Information
We find that phone contact has better immediate results over using email.
Let us know how it goes please.


Well, this camera continues to have glitches as of August.02.2018
Yeah the motion is alerting about every 5 to 10 minutes randomly for me.
Usually caused by a cloud or angle of sunlight or the ir shutter switching or neighborhood ac voltage level change of plus or minus 0.05 volts (like if the neighbor's cooler turns on.)
0 to 29 percent is lots of alerts, 30 to 46 is a few less, 47 to 100 is same as 0 to 29.

Still wont reboot if after system crash, have to unplug and plug back in, though it does seem to crash less with the 1.04.01 update.
Wifi "seems" somewhat better or more stable with 1.04.01 update.
The time to live view in the apps for this camera still takes about 10 to 20 seconds at least to load.

Video quality is good after loading time.

I have tried downgrading the firmware to 1.03 and 1.01, the number of alerts is a tiny fewer but not much, but the previous firmwares have a lot of other problems though that make it difficult to set motion and percentage correctly at all.

This is my general observations of this camera, it is NOT a full log of every glitch I have experienced with the 2530L.

Logged
"Nothing Funny about It...." We are not here to Impress anyone! You have a be a COMPETENT user first to under stand COMPETENT help!