• July 20, 2019, 12:43:50 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Pages: 1 [2]

Author Topic: 5020L not reconnecting remotely after power outage (but OK on local wifi)  (Read 11598 times)

RYAT3

  • Level 10 Member
  • *****
  • Posts: 2110

It sounds like you can log into your router.

Does the camera have an IP address? Set up port forwarding to the camera if it does.  make 8300 point to the 192.168.x.y:80
You should be able to login to the camera's F/W webpage to access?
Logged

Belviking

  • Level 1 Member
  • *
  • Posts: 5

Dear RYAT3,
I do have an other camera connected to the remote modem but other than changing the password there is nothing I can change on the remote device.  Changing port forwarding settings is not possible.  Grrrrr.
Since I can access my other camera I could imagine I could also ping the unavailable camera?
Any advise?
John
Logged

RYAT3

  • Level 10 Member
  • *****
  • Posts: 2110


I'm not sure you follow me.

Which router do you have?  Do you know the admin/password for the router?  Can you log into the router remotely?
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47578
  • D-Link Global Forum Moderator
    • Router Troubleshooting

Link>Welcome!
What Mfr and model is the ISP modem?
What Mfr and model is the main host router?
What wireless modes are you using?
What is the distance between the Camera and the main host router?
How many other wireless devices do you have connected to the main host router?
  • Any 2.4Ghz or 5Ghz cordless house phones or WiFi APs near by that maybe causing interferences?
  • Any other WiFi routers in the area that maybe causing interferences? Link> Use a WiFi Scanner to find out. How many?

Test cameras with uPnP and uPnP Port Forwarding both enabled on ALL cameras: DCS Cloud (L) Series Camera Configuration and Mydlink.com

Hi,
I have a similar issue/question.  I did accept a firmware upgrade request (how stupid) and since then I do not have access anymore to my remote DCS-935L.

Any suggestions to regain access?  My camera is on a remote location and will not have access for several months.  A powercycle is not possible unless hoping for a grid interrupt.  I could restart the router remotely but I am afraid of loosing connection to an other camera I have on that location?  Any recommendations?

Thank you,

John
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting

Belviking

  • Level 1 Member
  • *
  • Posts: 5

@RYAT3

The remote modem is Zyxel but do not seem to be able to log into it.   Grrrrr

John
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47578
  • D-Link Global Forum Moderator
    • Router Troubleshooting

Any status on this?  ???
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting
Pages: 1 [2]