The Graveyard - Products No Longer Supported > DCH-S150

DCH-S150 registration

<< < (2/4) > >>

pilot773:

--- Quote from: Kakashi::. on August 09, 2016, 08:37:10 AM ---
Let us know how it goes.


--- End quote ---

Received an email from dlink support. It was more or less the procedure that is  in the (full) manual.
Yes, there is a 'full' manual and a short version. One has to find this. GOOGLE as a friend ;-)

In the email sent by the support, they suggested to reset and go through the manual procedure, no
WPS, step by step with the registration until the light is green on the DCH-S150.

Then wait for at least 2 minutes !!!

and after this continue in the app by giving a short name name for the device. They said, during this
2 min the device should register at the server - and YES, that was the solution for both of my devices.

with best regards from Vienna / Austria

pilot773

FurryNutz:
Sounds like the wait 2 minutes is needed when adding more than one of the same model. Glad it worked for you and it's working.

Enjoy.  ;)

pilot773:

--- Quote from: FurryNutz on August 10, 2016, 06:54:53 AM ---
Sounds like the wait 2 minutes is needed when adding more than one of the same model. Glad it worked for you and it's working.


--- End quote ---

one by one, step-by-step, as I tried at the very beginning did not work.
apparently the 2 min wait time was required. So I had the two working after this setup procedure.


--- Quote from: FurryNutz on August 10, 2016, 06:54:53 AM ---
Enjoy.  ;)


--- End quote ---

unfortunately I can not enjoy. unplugged both units for two hours. tried again
to plug both into mains. One of them shows 'offline'. But both are connected to my router.
Checked this in the router menu and used the app 'Fing' in Android. Both DCH-S150
having an local IP and are connected to the router.

So I logged off in my app, plugged out / plugged in both sensors, waited until they show green.
Logged in at the app, waited for 3 min, both of them show 'offline' in my app.

The message: 'Your device can not register (login) in the Internet...
(german language, I tried to translate..) if I tap on one of them in the 'my devices' tab.

I think the problem is still the communicatio between sensor and the dlink server in the cloud.
If a unit can not register at the server, timing or whatever problem, I see it 'offline'.

For the time being I GIVE UP. The sensor setup is unreliable and unpredictable - wasted money :-(

with best regards from Vienna / Austria

pilot773

FurryNutz:
Just curious if you had them online and running, why did you power them off for two hours?  ???

Did you plug one in first and test to see if you could access it then wait 2 or more minutes before plugging in the next unit?

pilot773:

--- Quote from: FurryNutz on August 10, 2016, 07:45:48 AM ---Just curious if you had them online and running, why did you power them off for two hours?  ???

--- End quote ---

plan was, to have them programmed, prepared and if we leave the house for a day or more to set
it up as an alarm. I did not want to have them sucking power all the time. Looks like that does not work.

Btw. now I removed both devices from 'my devices' (swipe to the right, click on trash bin) and started
the registration process all over. Did wait as suggested by dlink support - NO, this does not work again.
Entering a name and try to finish - green circle for a while and the message that it can not register the
device in my account comes up again.

If I terminate the app and log in my account again it says immediately 'A new device has been found..'
It goes to the screen where one has to give a name for the device. Entering a name and try to finish
 - green circle for a while and the message that it can not register the device in my account comes up again.

rgds

Navigation

[0] Message Index

[#] Next page

[*] Previous page

Go to full version