• October 19, 2019, 08:50:27 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Pages: 1 2 3 [4]

Author Topic: New - DIR-880L FW v1.07 - Beta Release - NA Region!  (Read 13936 times)

Eluder

  • Level 2 Member
  • **
  • Posts: 49
Re: New - DIR-880L FW v1.07 - Official Beta Release - NA Region!
« Reply #45 on: May 20, 2016, 09:40:53 AM »

Hi Furry,

No, SmartConnect was disabled.
No, wired connections don't exhibit this issue, only wireless clients.
Yes, I (re)loaded the official release, though there is no difference between B08 and the final (I did the binary comparison on those two bins).

Let me know if you need any other information.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47844
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: New - DIR-880L FW v1.07 - Official Beta Release - NA Region!
« Reply #46 on: May 20, 2016, 10:29:49 AM »

Ok.

Does the same thing happen if you have SC enabled?
What wireless modes, channels and security modes were you using with SC disabled?

Hi Furry,

No, SmartConnect was disabled.
No, wired connections don't exhibit this issue, only wireless clients.
Yes, I (re)loaded the official release, though there is no difference between B08 and the final (I did the binary comparison on those two bins).

Let me know if you need any other information.
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting

Eluder

  • Level 2 Member
  • **
  • Posts: 49
Re: New - DIR-880L FW v1.07 - Official Beta Release - NA Region!
« Reply #47 on: May 20, 2016, 12:53:52 PM »

I'm pretty sure it does do it with SC, not sure I want to flash to 1.07 just to test things out, but I'll see.

In terms of the modes, etc
I was using both 2.4 and 5GHz and tried multiple channels (used a tool to scan for open channels and put my networks on channels with NO other network in use), security was WPA2.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47844
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: New - DIR-880L FW v1.07 - Official Beta Release - NA Region!
« Reply #48 on: May 20, 2016, 12:58:43 PM »

Ok, just looking for all the details. I did find one issue with SC when enabled, I'm seeing two SSID names instead of one. Just checking to see if others saw this as well.

I'm sure D-Link will fix all of this. Just want to give them all info needed.

Thanks.
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting

Eluder

  • Level 2 Member
  • **
  • Posts: 49
Re: New - DIR-880L FW v1.07 - Official Beta Release - NA Region!
« Reply #49 on: May 20, 2016, 03:42:35 PM »

I appreciate you trying to help... I don't recall seeing two networks with SC enabled, but it's possible I wasn't using the current v1.07 that is out there. It may have been one of the earlier betas, or even 1.06.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47844
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: New - DIR-880L FW v1.07 - Official Beta Release - NA Region!
« Reply #50 on: May 20, 2016, 03:51:50 PM »

I think all do a full manual reload on mine and see what happens.
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting

nettewurk

  • Level 3 Member
  • ***
  • Posts: 174
Re: New - DIR-880L FW v1.07 - Official Beta Release - NA Region!
« Reply #51 on: May 30, 2016, 11:38:05 PM »


Hello to everyone,

After installing it without factory resetting, the smart connect didn't correct single visible SSID but seen as 2 SSID I configured before.  Tried again from factory reset but resolved this problem. 

But after fully checking its performance with pingtest of OOKLA, ping response time or latency is higher compared to previous version, more than 100ms, unlike with previous 10-20ms.  Had tried to test this again and again for how many days but still getting high latency problem.  I assume that my ISP didn't change any of their system setting because the IPs assigned to me are the same, likewise the gateway and DNS IPs.   Even non-peak periods show the above problem.  Another one is the WiFi/LAN card cannot be displayed correctly, regardless of 802.11b/g/n/ac or phone/notebook PC/tablet PC.

But these for me are all OK specially the QOS settings resovled.   Maybe expecting 1.08WW for these in the near future :)
Logged
DIR/DCS/DNS

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47844
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: New - DIR-880L FW v1.07 - Official Beta Release - NA Region!
« Reply #52 on: May 31, 2016, 06:51:25 AM »

Thanks for the confirmation that the SSID name issue was resolved.

Have you see this issue reported here:
http://forums.dlink.com/index.php?topic=59562.0
Regarding 5Ghz Guest Zone enabled when SC is enabled?

And to confirm you are using FW version located here correct? http://forums.dlink.com/index.php?topic=64891.0


Hello to everyone,

After installing it without factory resetting, the smart connect didn't correct single visible SSID but seen as 2 SSID I configured before.  Tried again from factory reset but resolved this problem. 

But after fully checking its performance with pingtest of OOKLA, ping response time or latency is higher compared to previous version, more than 100ms, unlike with previous 10-20ms.  Had tried to test this again and again for how many days but still getting high latency problem.  I assume that my ISP didn't change any of their system setting because the IPs assigned to me are the same, likewise the gateway and DNS IPs.   Even non-peak periods show the above problem.  Another one is the WiFi/LAN card cannot be displayed correctly, regardless of 802.11b/g/n/ac or phone/notebook PC/tablet PC.

But these for me are all OK specially the QOS settings resovled.   Maybe expecting 1.08WW for these in the near future :)

Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting

nettewurk

  • Level 3 Member
  • ***
  • Posts: 174
Re: New - DIR-880L FW v1.07 - Beta Release - NA Region!
« Reply #53 on: June 01, 2016, 01:32:18 AM »



See my inline comments below:

>Have you see this issue reported here:
>http://forums.dlink.com/index.php?topic=59562.0
>Regarding 5Ghz Guest Zone enabled when SC is enabled?
Mine, the guest zone is disabled even after SC was enabled.

>And to confirm you are using FW version located here correct? http://forums.dlink.com/index.php?topic=64891.0
Got my version from D-Link Technical Support Asia (http://tsd.dlink.com.tw/downloads2008detailgo.asp)



Logged
DIR/DCS/DNS

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47844
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: New - DIR-880L FW v1.07 - Beta Release - NA Region!
« Reply #54 on: June 01, 2016, 06:45:02 AM »

Thank you for the info.

Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting
Pages: 1 2 3 [4]