• December 05, 2019, 04:09:58 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Pages: 1 [2]

Author Topic: DNS-320 (RevB2): how to break u-boot  (Read 23158 times)

emuluke

  • Level 1 Member
  • *
  • Posts: 3
Re: DNS-320 (RevB2): how to break u-boot
« Reply #15 on: November 24, 2014, 09:47:01 AM »

Where did you solder the GND to? And what settings did you use for console program?

Hello,  I put the gnd attached to the gnd pole of the fan.  I used same settings as the first post.
I will now try to invert TX and rx cables
Will post

Logged

albert

  • Level 5 Member
  • *****
  • Posts: 510
    • SoHo NAS Forum
Re: DNS-320 (RevB2): how to break u-boot
« Reply #16 on: November 24, 2014, 05:10:24 PM »

Hello,  I put the gnd attached to the gnd pole of the fan.  I used same settings as the first post.
I will now try to invert TX and rx cables
Will post

Yes, that's the cause, TXD & RXD pin need to be reverse on the NAS side. And try to solder GND to pin 4 instead of using the fan GND pin

Also remember to check the driver settings under Device Manager, IIRC the default is set to 9600 baud.
« Last Edit: November 24, 2014, 05:12:04 PM by albert »
Logged
D-Link DNS-320 rev A1 (FW: 2.05) [FFP-0.7]
PCI NAS-01G (FW: Encore ENNHD-1000 4.10)
PCI NAS-01G (FW: OpenNAS 1.9]

emuluke

  • Level 1 Member
  • *
  • Posts: 3
Re: DNS-320 (RevB2): how to break u-boot
« Reply #17 on: March 12, 2015, 11:56:16 AM »

I MADE IT! I am into the serial console prompt, as ROOT.
Joy oh joy.
Now the thing is that I need to pass the correct commands to un-brick my NAS....
Let's do some research... again
Logged

albert

  • Level 5 Member
  • *****
  • Posts: 510
    • SoHo NAS Forum
Re: DNS-320 (RevB2): how to break u-boot
« Reply #18 on: March 25, 2015, 06:37:33 AM »

Let me know if you still having problem in un-bricking your NAS.
Logged
D-Link DNS-320 rev A1 (FW: 2.05) [FFP-0.7]
PCI NAS-01G (FW: Encore ENNHD-1000 4.10)
PCI NAS-01G (FW: OpenNAS 1.9]

sparomba

  • Level 1 Member
  • *
  • Posts: 14
Re: DNS-320 (RevB2): how to break u-boot
« Reply #19 on: April 02, 2015, 02:06:08 AM »

@ emuluke:
Can you please post the commands you used to un-brick your NAS from within uBoot?


I bricked my DNS-320L after a firmware upgrade. I have access to the serial port can use the uBoot console.
I can transfer the original firmware(DLINK_DNS320L(LW).1.04b12) image to the NAS through tftp, but how do I go from there?

I never used uBoot before and need a little guidance. Maybe it's possible to modify your way of unbricking the DNS-320 to unbrick a DNS-320L...
« Last Edit: April 02, 2015, 02:08:27 AM by sparomba »
Logged
Pages: 1 [2]