• February 24, 2021, 06:43:10 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  


This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: DAP-1155 Bridge Continuously disconnecting  (Read 2702 times)


  • Level 1 Member
  • *
  • Posts: 2
DAP-1155 Bridge Continuously disconnecting
« on: December 12, 2014, 06:07:31 AM »


I have recently purchase a DAP-1155 to use as a wireless bridge. but it keeps getting disconnected every 10 minutes.
I went through the wizard and set it up as a wireless bridge, then went ahead and connected it to the device I wanted to use. Everything was fine for about 10 minutes, but then it got disconnected.
I also read the following thread:
http://forums.dlink.com/index.php?topic=58474.msg230280#msg230280 but that one is using the device as an access point, not a bridge. So not that helpful.

I'm using a Linksys E4200 Wireless router which is a pretty powerful device and I'm sure it's not the cause of my problems.
I have changed the 802.11 Mode and it did not work, also tried both 20MHz and the Auto channel width options, no luck either!

It is really frustrating and I would really appreciate any help you guys can give me.

Kind regards


  • Level 1 Member
  • *
  • Posts: 2
Re: DAP-1155 Bridge Continuously disconnecting
« Reply #1 on: December 12, 2014, 06:22:53 AM »

I have to say that I've been using a DAP-1360 as a repeater for quite some time without any issues at all.
I should also let you know that I currently reside in Iran/Tehran (since I've seen it's one of the first questions you guys ask).

Kind regards


  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49520
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DAP-1155 Bridge Continuously disconnecting
« Reply #2 on: December 15, 2014, 08:47:42 AM »


  • What Hardware version is your DAP? Look at sticker under the DAPs case.
  • Link>What Firmware version is currently loaded? Found on the DAPs web page under status.
  • What region are you located?
  • What wireless modes are you using on the main host router?
  • 2.4Ghz and 5Ghz routers: Try single mode G or N or mixed G and N on 2.4Ghz and single mode N or AC on 5Ghz?
  • Channel Width set for Auto 20/40Mhz or try 20Mhz only.
  • Try setting a manual Channel to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear. 13 for EU regions. Try channel 48 or 149 on 5Ghz.
  • What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES, so you might want to try TPIK only or Auto TPIK and AES.
  • Any 2.4Ghz or 5Ghz cordless house phones or WiFi APs near by that maybe causing interferences?
  • Any other WiFi routers in the area that maybe causing interferences? Link> Use InSSIDer to find out. How many? Use v3, its free.
Cable: 1Gb/50Mb>NetGear CAX80>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.