• April 03, 2020, 11:25:56 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Can't connect to my server outside of LAN  (Read 10271 times)

mniel0

  • Level 1 Member
  • *
  • Posts: 7
Can't connect to my server outside of LAN
« on: September 09, 2013, 03:02:16 AM »

Hi Guys. I am currently trying to connect with remote desktop (VNC) (Port 5900) from outside of my Local area network. However i am not allowed too. I can connect from my laptop to my server (on the same network..) without problems, so im kind of out of ideas..

(I have reserved 192.168.0.2 for my server, and ofcourse port forwarded with 192.168.0.2 etc)

Tell me if u need any additional information

Thank you


Kind regards - Internet noob..
« Last Edit: September 13, 2013, 12:34:53 AM by mniel0 »
Logged

mniel0

  • Level 1 Member
  • *
  • Posts: 7
Re: Does the 865L support VLAN?
« Reply #1 on: September 09, 2013, 03:59:02 AM »

 Nevermind, the ISP told me that they would send me a new box for free because of their mistake :-).


/END
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 48530
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Does the 865L support VLAN? FIXED (RESOLVED)
« Reply #2 on: September 09, 2013, 06:53:03 AM »

Link>Welcome!
    The DIR-865L is a WiFi/Router. VLANs are usually on network switches.

    Glad you got it figured out.

    Good Luck.
Logged
"Nothing Funny about It...." We are not here to Impress anyone! You have a be a COMPETENT user first to under stand COMPETENT help!

mniel0

  • Level 1 Member
  • *
  • Posts: 7
Re: Can't connect to my server outside of LAN FIXED
« Reply #3 on: September 12, 2013, 01:22:12 PM »

new problem.. help :-)
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 48530
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Can't connect to my server outside of LAN FIXED
« Reply #4 on: September 12, 2013, 01:41:40 PM »

 ???
Logged
"Nothing Funny about It...." We are not here to Impress anyone! You have a be a COMPETENT user first to under stand COMPETENT help!

mniel0

  • Level 1 Member
  • *
  • Posts: 7
Re: Can't connect to my server outside of LAN FIXED
« Reply #5 on: September 12, 2013, 02:17:34 PM »

???

Read #0 again..

For some reason i am unable to reach my server from outside of my LAN.. port forwards is done right (Both done it by hand and by a program ive been using a lot)..

I have also tried to use a listener on my server and then try to connect (port 5900..) timed out and the listener did not find anything..

any suggestions? (Already checked for firewalls etc... nothing.)
« Last Edit: September 12, 2013, 02:19:10 PM by mniel0 »
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 48530
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Can't connect to my server outside of LAN FIXED
« Reply #6 on: September 12, 2013, 02:21:00 PM »

      Link>
Welcome!
  • What Hardware version is your router? Look at sticker under router.
  • Link>What Firmware version is currently loaded? Found on the routers web page under status.
  • What region are you located?

Internet Service Provider and Modem Configurations
  • What ISP Service do you have? Cable or DSL?
  • What ISP Modem Mfr. and model # do you have?
  • What ISP Modem service link speeds UP and Down do you have?
  • Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask. Link>Checking MTU Values
  • For DSL/PPPoE connections on the router, ensure that "Always ON" option is enabled.

Router and Wired Configurations
Some things to try: - Log into the routers web page at 192.168.0.1. Use IE, Opera or FF to manage the router.
  • Turn off ALL QoS or Disable Traffic Shaping (DIR only) GameFuel (DGL only and if ON.) options, Advanced/QoS or Gamefuel.
  • Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual or under Setup/PARENTAL CONTROL/Set to>None: Static IP or Obtain Automatically From ISP.
  • Enable Use Unicasting (compatibility for some ISP DHCP Servers) under Setup/Internet/Manual.
  • Turn on DNS Relay under Setup/Networking. Link>Finding Faster DNS Addresses using Name Bench
  • Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting.
  • Ensure devices are set to auto obtain an IP address.
  • If IPv6 is an option on the router, select Local Connection Only or Disable IPv6 options under Setup/IPv6.
  • Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall. Enable or Disable SPI to test.
  • Enable uPnP and Multi-cast Streaming under Advanced/Networking. Disable uPnP for testing Port Forwarding rules. Enable IPv6 Multi-cast Streaming for routers that have a Media Server option. Disable IPv6 Multi-cast Streaming if IPv6 or Media Server is not being used.
  • Turn off WISH, and WPS under Advanced.
  • WAN Port Speed set to Auto or specific speed? Some newer ISP modems support 1000Mb so manually setting to Gb speeds can be supported by the router. Advanced/Advanced Networking/WAN Port Speed
  • Set current Time Zone, Date and Time. Use an NTP Server feature. Tools/Time.


Try using Virtual Server rules as an alternate to Port Forwarding as a test.
Logged
"Nothing Funny about It...." We are not here to Impress anyone! You have a be a COMPETENT user first to under stand COMPETENT help!

mniel0

  • Level 1 Member
  • *
  • Posts: 7
Re: Can't connect to my server outside of LAN FIXED
« Reply #7 on: September 12, 2013, 02:46:41 PM »

      Link>
Welcome!
  • What Hardware version is your router? Look at sticker under router.
  • Link>What Firmware version is currently loaded? Found on the routers web page under status.
  • What region are you located?

Internet Service Provider and Modem Configurations
  • What ISP Service do you have? Cable or DSL?
  • What ISP Modem Mfr. and model # do you have?
  • What ISP Modem service link speeds UP and Down do you have?
  • Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask. Link>Checking MTU Values
  • For DSL/PPPoE connections on the router, ensure that "Always ON" option is enabled.

Router and Wired Configurations
Some things to try: - Log into the routers web page at 192.168.0.1. Use IE, Opera or FF to manage the router.
  • Turn off ALL QoS or Disable Traffic Shaping (DIR only) GameFuel (DGL only and if ON.) options, Advanced/QoS or Gamefuel.
  • Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual or under Setup/PARENTAL CONTROL/Set to>None: Static IP or Obtain Automatically From ISP.
  • Enable Use Unicasting (compatibility for some ISP DHCP Servers) under Setup/Internet/Manual.
  • Turn on DNS Relay under Setup/Networking. Link>Finding Faster DNS Addresses using Name Bench
  • Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting.
  • Ensure devices are set to auto obtain an IP address.
  • If IPv6 is an option on the router, select Local Connection Only or Disable IPv6 options under Setup/IPv6.
  • Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall. Enable or Disable SPI to test.
  • Enable uPnP and Multi-cast Streaming under Advanced/Networking. Disable uPnP for testing Port Forwarding rules. Enable IPv6 Multi-cast Streaming for routers that have a Media Server option. Disable IPv6 Multi-cast Streaming if IPv6 or Media Server is not being used.
  • Turn off WISH, and WPS under Advanced.
  • WAN Port Speed set to Auto or specific speed? Some newer ISP modems support 1000Mb so manually setting to Gb speeds can be supported by the router. Advanced/Advanced Networking/WAN Port Speed
  • Set current Time Zone, Date and Time. Use an NTP Server feature. Tools/Time.


Try using Virtual Server rules as an alternate to Port Forwarding as a test.

Hardware version : A1
Firmware: 1. 05
Region : EU

ISP AND MODEM CONFIG.
-Cable
-Allied telesyn at-rg613xt
-80/80mbit
-mtu at 1500

Router and Wired Configurations
-QoS disabled.
-All dns disabled (not sure, Will check)
-i have set up a reserved IP adress for most devices.
-havent Tried to disabled ipv6 (not Even sure its On)
-upnp and stream On.
-havent Tried to disabled pnp for port forward check (Will do tomorrow)
-wan port speed automatic.
-already Tried with virtuel server instead of port forward.. Did not seem to work..

Thanks [/list][/list]
Logged

mniel0

  • Level 1 Member
  • *
  • Posts: 7
Re: Can't connect to my server outside of LAN FIXED
« Reply #8 on: September 13, 2013, 12:20:30 AM »

I have now tried everything you suggested..

Still wont work :(




https://www.dropbox.com/sh/zy8gwqhg8aezk8x/6BuhkgDW-3
https://www.dropbox.com/s/8z7s48v5w3a0ifx/Unavngivet.png
Logged

mniel0

  • Level 1 Member
  • *
  • Posts: 7
Re: Can't connect to my server outside of LAN
« Reply #9 on: September 13, 2013, 01:41:10 AM »

Wow, for some reason my ISP firewall turned on again for some odd reason...


I disabled it and it is now working.. how annoying.


thanks for ur help anyways
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 48530
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Can't connect to my server outside of LAN (RESOLVED)
« Reply #10 on: September 13, 2013, 06:54:59 AM »

Did you use Virtual Server or Port Forwarding?

Glad you got it working.

Enjoy.
Logged
"Nothing Funny about It...." We are not here to Impress anyone! You have a be a COMPETENT user first to under stand COMPETENT help!