• March 20, 2019, 12:06:00 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: multiple wan configuration (adsl/fiber optic/broadband)connection guide dsl 2750  (Read 21038 times)

nabilano

  • Level 1 Member
  • *
  • Posts: 9

hello for every body
this  is for multiple methode connection guide for dsl 2750u
1-adsl
2-fiber optic
3-broadband
for dsl 2750u model
DSL-2750U CONFIGURATION GUIDE
 
For ADSL Connection
1. Open Internet Explorer and type http://192.168.1.1 on the address bar. Type “admin”on both the username and password field.
2.  Click Advanced Setup > Layer 2 Interface > ATM interface. Click Add.
3.  Under ATM PVC Configuration set the following:
 VPI=
 VCI=
DSL Link Type= select EOA for PPPoE otherwise select PPPoA (call ISP to verify your connection type and VCI-VPI values)
Encapsulation: LLC/Encapsulation

Click Apply/Save

4.  Click Advanced Setup > WAN Service. Click Next

5. Type the username and password .

6. Under routing- Default Gateway, click next.

7. Under DNS Server Configuration, click next.

8. Under WAN/ Setup Summary, click Apply/ Save.


For Fiber Optic Connection
1.   Open Internet Explorer and type http://192.168.1.1 on the address bar. Type “admin”on both the username and password field.
2.  Click Advanced Setup > Layer 2 Interface > ETH interface. Click Add.
3. Under ETH WAN configuration, select Default Mode. Click Apply/ Save
4. Click Advanced Setup > WAN Service. Click Next.
5.  Under WAN Service configuration, select PPP over Ethernet, click next.
6.  Under PPP Username and password, type the username and password provided by your ISP. Click next.
6. Under routing- Default Gateway, click next.

7. Under DNS Server Configuration, click next.

8 . Under WAN/ Setup Summary, click Apply/ Save.

For Broadband Connection
1.   Open Internet Explorer and type http://192.168.1.1 on the address bar. Type “admin”on both the username and password field.
2.  Click Advanced Setup > Layer 2 Interface > ETH interface. Click Add.
3. Under ETH WAN configuration, select Default Mode. Click Apply/ Save
4. Click Advanced Setup > WAN Service. Click Next.
5.  Under WAN Service configuration, select IP over Ethernet, click next.
6. Under WAN/ IP Settings click next.
7.  Under Network Address Translation, select Enable NAT, click next.
8. Under routing- Default Gateway, click next.

9. Under DNS Server Configuration, click next.

10. Under WAN/ Setup Summary, click Apply/ Save.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47033
  • D-Link Global Forum Moderator
    • New DIR-890L Router with SmartConnect™ Technology

Any reboots or power cycles that need to happen after these configurations are applied?
Logged
"Nothing Funny about It...." We are not here to Impress anyone! You have a be a COMPETENT user first to under stand COMPETENT help!

nabilano

  • Level 1 Member
  • *
  • Posts: 9

Yes the reboot is recommended.
« Last Edit: May 07, 2013, 04:04:45 PM by FurryNutz »
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47033
  • D-Link Global Forum Moderator
    • New DIR-890L Router with SmartConnect™ Technology

Thank you for sharing this information. I'll review it and recommend it be placed into a sticky for future references.

Logged
"Nothing Funny about It...." We are not here to Impress anyone! You have a be a COMPETENT user first to under stand COMPETENT help!