• September 25, 2020, 08:10:51 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: DIR 655 OOPS THIS PAGE CANNOT BE LOADED  (Read 3692 times)

shinglewood

  • Level 1 Member
  • *
  • Posts: 1
DIR 655 OOPS THIS PAGE CANNOT BE LOADED
« on: July 02, 2012, 09:15:42 AM »

GUYS
URGENT URGENT......I BOUGHT THIS DIR 655 B1 DLINK EUROPEAN ROUTER. HOW THE HELL DO I GET RID OF THESE OOPS SCREENS THAT I SEE MANY FOLK GET....SO ANNOYING

THANKS
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49210
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DIR 655 OOPS THIS PAGE CANNOT BE LOADED
« Reply #1 on: July 02, 2012, 09:20:11 AM »

Link>Welcome!

Link>What Firmware version is currently loaded? Found on routers web page under status.
What region are you located?
Are you wired or wireless connected to the router?
What browser are you using?
Try Opera or FF? If IE 8 or 9, set compatibility mode and test again. Happen with these browsers?


What ISP Service do you have? Cable or DSL?
What ISP Modem do you have? Stand Alone or built in router?
What ISP Modem make and model do you have?
If this modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems.
Double NAT
To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged.
If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ.

Some things to try:
Turn off ALL QoS or Disable Traffic Shaping (DIR only) GameFuel (DGL only and if ON.) options. Advanced/QoS or Gamefuel.
Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual.
Turn on DNS Relay under Setup/Networking.
Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking
Ensure devices are set to auto obtain an IP address.
Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall.
Enable uPnP and Multi-cast Streaming under Advanced/Networking.


Link>Wireless Installation Considerations
What wireless modes are you using? Under Setup/Wireless/Manual.
Try single mode G or N or mixed G and N?
Channel Width set for Auto 20/40Mhz or try 20Mhz only.
Try setting a manual channel to a open or unused channel.
What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES, so you might want to try TPIK only or Auto.
What wireless devices do you have connected?
Any cordless house phones?
Any other WiFi routers in the area? Use InSSIDer to find out. How many?
Turn off WISH, and WPS under Advanced.
Try turning off Short GI, WLAN Partition,and Extra Wireless Protection if you have it. Under Advanced/Advanced Wireless.

Turn off all anti virus and firewall programs on PC while testing. 3rd party firewalls are not generally needed when using routers as they are effective on blocking malicious inbound traffic.
Turn off all devices accept for one wired PC while testing.

Check cable between Modem and Router, swap out to be sure. Cat6 is recommended.
Logged
"Nothing Funny about It...." We are not here to Impress anyone! You have a be a COMPETENT user first to under stand COMPETENT help!