• November 15, 2019, 03:19:47 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Dir-815 port forwarding problem  (Read 3979 times)

NicEShoT

  • Level 1 Member
  • *
  • Posts: 1
Dir-815 port forwarding problem
« on: June 21, 2012, 01:30:30 AM »

hey guy I just got a dir-815 and i am having problems with port forward, the first time I port forwarded it worked, but then when i deleted the port, it stopped working, it saves, but it doesn't open....

can you help me please?
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47908
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Dir-815 port forwarding problem
« Reply #1 on: June 21, 2012, 07:06:11 AM »

Link>Welcome!
What Hardware version is your router? Look at sticker under router.
Link>What Firmware version is currently loaded? Found on routers web page under status.
What region are you located?
Are you wired or wireless connected to the router?

What ISP Service do you have? Cable or DSL?
What ISP Modem do you have? Stand Alone or built in router?
What ISP Modem make and model do you have?
If this modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems.
To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged.
If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ.

Some things to try:
Try a factory reset first, then try to set up the port forward rule again.
Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking
Ensure devices are set to auto obtain an IP address.
Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall.
Enable uPnP and Multi-cast Streaming under Advanced/Networking.

Also if you get it working, save the routers configuration to file too when your done.
« Last Edit: June 22, 2012, 06:51:49 AM by FurryNutz »
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47908
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Dir-815 port forwarding problem
« Reply #2 on: December 06, 2012, 12:26:28 PM »

I know is this old however, any status on this?  ???
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting