• September 19, 2019, 01:14:44 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Pages: 1 [2]

Author Topic: DCS-932l wireless not working  (Read 111420 times)

musicrab

  • Level 1 Member
  • *
  • Posts: 1
Re: DCS-932l wireless not working
« Reply #15 on: November 30, 2012, 05:27:36 AM »

Grrr. Camera cannot handle WPA2/WPA Mixed Mode security.  Set it to plain and simple WPA2 and it works (as above). Grrr.
Logged

arunchacko

  • Level 1 Member
  • *
  • Posts: 1
Re: DCS-932l wireless not working
« Reply #16 on: March 09, 2013, 10:51:22 PM »

This is an old thread, but maybe folks are still coming here to try to find answers.   I also had a LOT of trouble trying to get my 932L to communicate with my router (Cisco E3500) wirelessly.  It would do just fine as long as the Cat5 cable was connected, but refused to work once the cable was unplugged. 
Security on the camera was set to WPA-PSK / WPA2-PSK.    Security on my router was set to  WPA2/WPA Mixed Mode.   Changing my router security to   WPA2 Personal  was all it took to fix the wifi problem.  Hopefully this information will help someone out there.  I was on the verge of returning my 932l to BestBuy, and now I'm glad I didn't.


SequiMike, your suggestion saved my day...I was about to return it..
Logged

pamsbob

  • Level 1 Member
  • *
  • Posts: 1
Re: DCS-932l wireless not working
« Reply #17 on: July 17, 2013, 09:10:24 AM »

I have been fighting this same problem for weeks without luck, but I finally stumbled across a solution which may be of value to someone. I have an older 2wire wireless modem which uses WEP for security. The password for the modem is a 10 digit number, but the camera would only accept 13 digits for 128 encryption, and 5 digits for 64. I played with combinations since I had run out of ideas. I found that selecting 64 bit HEX for the key did the trick. It accepted my 10 digit key, and the camera connected wireless. Good luck.
Logged

diegodiazespinoza

  • Level 1 Member
  • *
  • Posts: 1
Re: DCS-932l wireless not working
« Reply #18 on: February 02, 2014, 03:48:03 PM »

Thanks for the support. In my case the issue was with a Cisco router WRT120N and DCS 932L. Didnt find the option "mixed" but change the encription from TKIP/AES to just only AES.
Logged

darkheim

  • Level 1 Member
  • *
  • Posts: 1
Re: DCS-932l wireless not working
« Reply #19 on: May 07, 2014, 04:09:17 PM »

This is an old thread, but maybe folks are still coming here to try to find answers.   I also had a LOT of trouble trying to get my 932L to communicate with my router (Cisco E3500) wirelessly.  It would do just fine as long as the Cat5 cable was connected, but refused to work once the cable was unplugged. 
Security on the camera was set to WPA-PSK / WPA2-PSK.    Security on my router was set to  WPA2/WPA Mixed Mode.   Changing my router security to   WPA2 Personal  was all it took to fix the wifi problem.  Hopefully this information will help someone out there.  I was on the verge of returning my 932l to BestBuy, and now I'm glad I didn't.

SequiMike, I joined the forums just to thank you. After an hour of troubleshooting I was able to install the camera by changing the router setting from WPA2 mixed to WPA2 personal.
Logged

ErwinC

  • Level 1 Member
  • *
  • Posts: 1
Re: DCS-932l wireless not working
« Reply #20 on: December 14, 2014, 05:49:35 AM »

This was really starting to irritate me. Glad I found this old thread. That is still apllies is a shame for D-link. Bought such a cam set 3 weeks ago and using most recent firmware.
Logged

RedYetiDave

  • Level 1 Member
  • *
  • Posts: 1
Re: DCS-932l wireless not working
« Reply #21 on: September 17, 2015, 02:25:28 AM »

And... it now works on a Thompson router and using WPA-PSK / WPA2-PSK, using the latest firmware; for Hardware revision B: 2.11. Which the mydlink site installs when you visit the camera (it takes a good few minutes so be patient).

  • Click Site Survey and select the network (so that's "Infrastructure" mode).
  • Select WPA-PSK / WPA2-PSK.
  • Enter the network key which the router uses (in my case, printed on the back by the telco).

Done! :)
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47759
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DCS-932l wireless not working
« Reply #22 on: September 17, 2015, 07:00:35 AM »

You might try using WPA2 only on the router if thats possible.
Also set a manual channel of 1, 6 or 11 if there not too busy or being used.

Enjoy.  ;)
And... it now works on a Thompson router and using WPA-PSK / WPA2-PSK, using the latest firmware; for Hardware revision B: 2.11. Which the mydlink site installs when you visit the camera (it takes a good few minutes so be patient).

  • Click Site Survey and select the network (so that's "Infrastructure" mode).
  • Select WPA-PSK / WPA2-PSK.
  • Enter the network key which the router uses (in my case, printed on the back by the telco).

Done! :)
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting

Hakaari

  • Level 1 Member
  • *
  • Posts: 1
Re: DCS-932l wireless not working
« Reply #23 on: June 22, 2019, 07:04:04 PM »

This is an old thread, but maybe folks are still coming here to try to find answers.   I also had a LOT of trouble trying to get my 932L to communicate with my router (Cisco E3500) wirelessly.  It would do just fine as long as the Cat5 cable was connected, but refused to work once the cable was unplugged. 
Security on the camera was set to WPA-PSK / WPA2-PSK.    Security on my router was set to  WPA2/WPA Mixed Mode.   Changing my router security to   WPA2 Personal  was all it took to fix the wifi problem.  Hopefully this information will help someone out there.  I was on the verge of returning my 932l to BestBuy, and now I'm glad I didn't.


@SequiMike  THANK YOU!!!!!!!   
I joined the forum just so I could thank you

Ive been trying for ages to get my cam up and running and tried a sh**ton of "fixes" ive found online...yours is the only one that has worked...you are a blessing mate. we need to keep this thread going for everyone else out there that stumbles across one of these cameras in a few years and starts looking for fixes online.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47759
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DCS-932l wireless not working
« Reply #24 on: June 23, 2019, 10:45:09 AM »

Glad it worked for you. Thanks for letting us know.
Enjoy.  ;)
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting
Pages: 1 [2]