• August 21, 2019, 03:44:21 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Apple Update Issue.  (Read 2979 times)

Corserip

  • Level 1 Member
  • *
  • Posts: 1
Apple Update Issue.
« on: May 22, 2015, 02:51:08 PM »

I recently bought the D-Link 803 Router, before this I had the plan Aztech router.
I never faced any issue with the Aztech router, but since I bought this new router I have been facing many issues.
The main issue is I can't update my mobile, I get the error 3014 which defines a connection error between apple servers and my internet.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47698
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Apple Update Issue.
« Reply #1 on: May 24, 2015, 09:08:02 AM »

Link>Welcome!

  • What Hardware version is your router? Look at sticker under the router case.
  • Link>What Firmware version is currently loaded? Found on the routers web page under status.
  • What region are you located?
  • Are you wired or wireless connected to the router?


Internet Service Provider and Modem Configurations
  • What ISP Service do you have? Cable or DSL?
  • What ISP Modem Mfr. and model # do you have?
  • Is ISP Modem/Service using Dynamic or Static WAN IP addressing?
  • What ISP Modem service link speeds UP and Down do you have?
  • By-pass the main host router and check internet connection by connecting a wired LAN PC directly to the ISP modem to verify connection access and ISP speeds.
  • Check cable between Modem and Router, swap out to be sure. Link> Cat6 is recommended.
  • Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask. Link>Checking MTU Values
  • For DSL/PPPoE connections on the router, ensure that "Always ON" option is enabled.

Wireless Configurations
Links>Wireless Installation Considerations and Managing Signal Congestion and Good Neighbour Policy
  • Ensure the default (dlink) SSID name is changed. Ensure that different SSID names are used between each WiFi 2.4/5Ghz radios. Can be anything and not something that's already in use by any neighbouring WiFi routers. Under Setup/Wireless/Manual.
  • What wireless modes are you using?
  • 2.4Ghz Routers only: Try single mode G or N or mixed G and N?
  • 2.4Ghz and 5Ghz routers: Try single mode G or N or mixed G and N on 2.4Ghz and single mode N or AC on 5Ghz?
  • Channel Width set for Auto 20/40Mhz or try 20Mhz only.
  • Try setting a manual Channel to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear. 13 for EU regions. Try channel 48 or 149 on 5Ghz.
  • What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES, so you might want to try TPIK only or Auto TPIK and AES.
  • What wireless devices do you have connected?
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting