• August 25, 2019, 06:10:51 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Access Control on local network  (Read 5193 times)

ojchase

  • Level 1 Member
  • *
  • Posts: 3
Access Control on local network
« on: January 31, 2015, 07:24:47 PM »

I'm wanting to prevent access to my media server, on my local network, on a fixed schedule.  The Access Control options work great for interacting with the outside web, but don't seem to do anything on the internal network.  I want to block all traffic to the device on a set schedule.  Is there a way to do this on the 601? 
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47713
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Access Control on local network
« Reply #1 on: February 01, 2015, 12:11:28 PM »

Link>Welcome!

  • What Hardware version is your router? Look at sticker under the router case.
  • Link>What Firmware version is currently loaded? Found on the routers web page under status.
  • What region are you located?

You can block access on the LAN side however this would be a complete cut off from internet as well...
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting

ojchase

  • Level 1 Member
  • *
  • Posts: 3
Re: Access Control on local network
« Reply #2 on: February 03, 2015, 09:41:10 PM »

Thanks for the response FurryNutz!  I've tried searching without much luck, so I'm glad to hear this can be done.

According to the 192.168.0.1 configuration page, I'm on "Hardware Version: A1" and "Firmware Version: 1.04NA".  I'm in Colorado, USA - is there a more specific region you're looking for, and if so where would I find it?
Edit: The physical router says 1.01NA, which I now see probably is North America for the region.  I don't recall updating the firmware from 1.01 to 1.04, but it's possible I did a long time ago or that I might've gotten the router secondhand.  I honestly don't remember!

Cutting off all internet access overnight is perfectly fine.  Ideally, it'd be nice to leave access to a couple sites so the DVR can update program info, but if that's not possible it's a tradeoff I'm willing to make.  Just as long as it comes back when the router schedule period is over the next day!
« Last Edit: February 03, 2015, 09:47:25 PM by ojchase »
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47713
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Access Control on local network
« Reply #3 on: February 05, 2015, 08:42:17 AM »

To set up scheduling:
1. Reserve device IP addresses ON the router under Setup/Networking.
2. Set up a schedule under Tools/Schedule on the routers web page. Customize your dates and times here.
3. Use Advanced/Access Control configured and apply the customized schedule to a policy and to the PC(s) or device(s) desired to be controlled. 
4. Ensure Time is set correctly on the router. Tools/Time.

I do believe Setup/Networking/DNS Relay and or Setup/Internet/Manual/Advanced DNS Services need to be enabled along with configuring Reserved IP addresses, Scheduling, and Access Controls.

Additional Info:
How to Block a specific port using Access Control: http://forums.dlink.com/index.php?topic=58731.0
How to set up Web Filters: http://www.dlink.cc/d-link-wireless/how-to-setup-website-filter-on-d-link-dir-series-router-dir-655.htm
How to Block FB: http://forums.dlink.com/index.php?topic=50490.0
Web Filter How To: http://forums.dlink.com/index.php?topic=5509.0
« Last Edit: February 05, 2015, 08:50:38 AM by FurryNutz »
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting

ojchase

  • Level 1 Member
  • *
  • Posts: 3
Re: Access Control on local network
« Reply #4 on: February 05, 2015, 08:51:35 AM »

Yes, I'd actually done that before posting.  (I believe I did it by mac address, not ip address though.)  It works great for blocking access outside my local network.  But the devices inside the network still seem to be able to talk to each other, which is what I'm trying to prevent.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47713
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Access Control on local network
« Reply #5 on: February 05, 2015, 08:54:10 AM »

I wonder if Mac Filtering would help...or setting up a wireless schedule where only certain times can devices access the wireless.   :-\
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 47713
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Access Control on local network
« Reply #6 on: February 05, 2015, 09:12:50 AM »

Are the other devices wireless? If they are, look for Advanced/Advanced Wireless/Wireless Partition or Isolation feature here. Enable it if you see it.

I updated this: Router Access Control, Blocking, Web Filters and Scheduling FAQ
Logged
Cable:200mb/10Mb>NetGear C7800>DIR-882>DGS-1100>HP 24pt Gb Switch. COVR-3902/2202/1203,DIR-2680,890L,882,880L,868L,DNR-202L,DNS-345x2,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting