D-Link Forums

D-Link Wireless Routers for Home and Small Business => COVR-3902-US => Topic started by: GreenBay42 on August 10, 2018, 10:10:07 AM

Title: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 10, 2018, 10:10:07 AM
EDIT - Firmware has been pulled off until proper upgrade instructions are provided
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 10, 2018, 11:13:50 AM
What's the order of the installation, I did the 03_middle one first and now my router can't find the extender.  I get a power light on and the 2 down arrows are green but the up arrows are not lit.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: FurryNutz on August 10, 2018, 11:15:32 AM
If you connect the extender to the base via LAN cable, can you access it's UI via IP address by chance?
 ???
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 10, 2018, 11:31:42 AM
I had it plugged in via LAN cable and ran the setup wizard and it couldn't find the extender, I am trying a couple of different things now and will let you know.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: FurryNutz on August 10, 2018, 11:40:32 AM
OK, I''ve notified D-Link about this. I think they forgot to include the upgrade steps.  ::)
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 10, 2018, 11:50:56 AM
I hard wired it to the router after doing a couple of resets so that it would get an IP.  Went in that way and installed the b11 version.  I think the issue is that during the 03_middle is restarted the extender too soon in the process.  I don't really use the extender just wanted to update to keep it fresh.  Will play some more and let you know.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 10, 2018, 12:07:06 PM
Yeah, I think the 03_middle hosed it, I was able to get the setup wizard to work when hard wired, but I still don't have the two uplink lights.  With the new b11 version, I can't go back to a lower version either.  I was NOT hardwired when I did the 03_middle upgrade, so maybe you will want to let people know that they may want to do both upgrades while wired to router.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 10, 2018, 12:22:36 PM
Thanks Dave for the feedback. I will notify them to add instructions. If the middle firmware disconnects it from the router this will cause some issues.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 10, 2018, 01:13:14 PM
I am pulling the firmware until I get upgrade instructions.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: FurryNutz on August 10, 2018, 01:16:10 PM
 ;)
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: FurryNutz on August 10, 2018, 01:17:02 PM
Were you able to get your extender running again or is it hosed?  ???

Yeah, I think the 03_middle hosed it, I was able to get the setup wizard to work when hard wired, but I still don't have the two uplink lights.  With the new b11 version, I can't go back to a lower version either.  I was NOT hardwired when I did the 03_middle upgrade, so maybe you will want to let people know that they may want to do both upgrades while wired to router.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 10, 2018, 01:58:27 PM
I am still just getting the two down arrow lights, up arrows are not lit.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: FurryNutz on August 10, 2018, 02:05:31 PM
Hopefully GreenBay can get some information. Hope the extender isn't bricked. If it is, I'm sure he can work with you to get it replaced.  ::)

Thought of something, might see if the extender has a recovery mode. Not sure if it does like the router does. Might check on this.


I am still just getting the two down arrow lights, up arrows are not lit.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 10, 2018, 02:23:22 PM
I can connect to it as long as its wired.  Did a factory reset on it and then ran the setup wizard but I don't thinks its retaining the settings as the password to log into the extender does not change with the wizard setup settings.

Tried to go back to the older firmware that is on support site but it won't let me downgrade.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 10, 2018, 02:25:08 PM
The "middle" firmware added encryption to the firmware so you cannot downgrade. I need to ask what (or if) the emergency/crash recovery procedure is for the extender.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 10, 2018, 02:26:36 PM
Can you skip the setup wizard and go directly to the upgrade page?
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 10, 2018, 02:31:32 PM
Can you skip the setup wizard and go directly to the upgrade page?

I can get to all the settings of the extender as long as I am wired to router,  can do firmware upgrades through upgrade page.

If I unplug the LAN cable  it is not seen on the network.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 10, 2018, 02:35:01 PM
I went back and re-read the entire thread....  ::)

Have you tried using the D-Link wi-fi app to setup the extender?

I sent emails asking for instructions and crash recovery procedures for the extender. There should be a way to hard wire a computer directly to the extender and access it...hopefully. 

What exactly happens when you run the wizard? Do you get errors?
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 10, 2018, 02:38:42 PM
What happened is that during the upgrade using the 03_middle file it restarted on its own at the 50% done instead of waiting to get to 100% and then restarting.  The upgrade window was still open during the reboot because I was watching it and the lights. The Upgrade webpage was still open and showing the completion percentage the whole time, the upgrade process  got to 100 it said process complete
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 10, 2018, 02:39:54 PM
The setup wizard completes just fine and says it is syncing the devices, but the extender doesn't retain the settings
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 10, 2018, 02:45:03 PM
Remember, its not a real big deal to me as I am not using the extender right now anyways.  Hopefully you pulled it quick enough that no one else was effected.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 10, 2018, 02:53:22 PM
That is strange that it would complete the wizard but not retain the settings. Thanks again for the info. I'm glad you are not dependent on the extender but this process should work without these issues and i agree hopefully no one else downloaded it.  :-[
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 13, 2018, 11:02:45 AM
To crash recover the extender:

1. Download an older firmware to your computer.
2. Connect the extender with an Ethernet cable directly to your computer. Set your computer a static IP of 192.168.0.2 / 255.255.255.0.
3. Hold in the reset button on the extender and unplug the power for 5 seconds and plug back in while holding the reset button down.
4. Keep holding until the LED turns red. Release. Give  a minute to boot.
5. Open IE 11 and go to http://192.168.0.50
6. The firmware recovery screen should appear. Load the firmware version you want.
7. Put your computer back to dhcp or whatever IP settings you had.
8. Press the WPS button on the extender and then the router. Wait 2 minutes.
9. Log into the router. Hopefully the extender is there? Run the wizard.

A tech is testing this now and hopefully will have the correct update instructions for the KRACK firmware.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 13, 2018, 01:50:05 PM
How long should I need to hold in the reset button?  I don't get a red light just a continuous blinking yellow.  Held it for 2 minutes just blinking yellow.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 13, 2018, 02:01:22 PM
A tech is testing the upgrade now. I will ask after he is done.

It usually takes like 10 seconds. As long as you were holding in the reset when the unit is off and held it as you plugged in the power, maybe it is yellow and not red.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 13, 2018, 02:17:31 PM
When I apply power with reset pressed in, I get a quick orange followed by 4 flashing yellows, a solid yellow for a few seconds and then just more flashing yellows
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 13, 2018, 02:49:25 PM
hmm ok. Can you connect to it? 192.168.0.50 should bring up a firmware recovery page.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 13, 2018, 02:54:45 PM
Can connect to it but don't get a recovery page, just the standard login page
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 13, 2018, 02:56:47 PM
Is there an actual html page for the recovery page that I could type directly into the browser?
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 13, 2018, 02:58:31 PM
When you crash recover, when you go to just the IP address (192.168.0.50) it is the only page that can display. If you get the regular login, it did not crash recover. The recovery page is actually in the boot loader separate from the firmware.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 13, 2018, 03:00:36 PM
I am betting the bootloader got hosed during the botched upgrade.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 13, 2018, 03:08:00 PM
So with the static IP on your computer you cannot connect? can you ping 192.168.0.50?
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 13, 2018, 03:09:43 PM
I CAN connect but don't get the recovery page just the standard login screen.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 13, 2018, 03:13:42 PM
If you want to, you can PM a link to the newer firmware, maybe it will overwrite something on the extender and make it work.  I tried the older versions but they won't install due the new encryption.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 13, 2018, 03:15:34 PM
OK. We will get this hammered out tomorrow. Not sure why it is not going into recovery mode. You are holding in the reset button as you turn the power on?  ;D

Try the latest firmware again. If you are getting to the login screen the boot loader is ok and but the settings not saving seems to be the main issue.

Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 13, 2018, 03:21:01 PM
Yep holding the reset in as I apply power.  I have a nice metal piece that came with a DVD drive I bought years ago, does a nice job of going into small holes to press buttons.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 13, 2018, 03:38:47 PM
Did firmware upgrade hard wired to laptop using FW110b11 version.  Extender rebooted itself at 65% point of the process.  NO change still getting the two green down arrow lights on the panel and no up arrow lights.  Still do not get the recovery page using reset/power on. 
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 13, 2018, 04:08:18 PM
Here is some more information for troubleshooting.

When I hold in the reset button and plug in the power the colors on the extender are the following:

Orange for a second or two followed by 4 yellow lights that blink and then a yellow light that is solid for a few seconds and then more blinking yellow.

When I release the reset button here is what happens:

If I release on the 3rd, 4th or 5th yellow lights the light stays solid for a second and then continues on with blinking yellow, extender does not reboot.

If I release the reset on the orange or first two yellows, they stay solid for a sec and the extender reboots.  When I log into the 192.168.0.50 page I do not get the recovery page just the standard login page.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 13, 2018, 08:16:57 PM
I got an email from the tech. He said he gets the login also and he replicated your issue. He uploaded both firmwares but the extender will not sync with the router. I will get more info tomorrow.

He said when holding the reset button and powered on, the light turned solid amber and he released. It blinked yellow and then turned green. He logged in and it went to the firmware page.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 13, 2018, 09:34:20 PM
Would you go to bed.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 13, 2018, 09:55:36 PM
Don't worry about it as I have now completely hosed it. tried uploading the b11 firmware again and said "let me try something"  so I powered off part way through the upgrade.  Now I get the orange light for a few seconds, yellow light for a few seconds, five fast blinking yellow lights and then solid yellow.  Can't get back to 192.168.0.50 page.

If I hold the reset in while applying power I get 4 slow blinking yellow, a solid yellow for a few seconds and then slow blinking yellow, when I release the reset button it continues the slow blinking yellow
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 14, 2018, 05:41:44 AM
Would you go to bed.

LOL I am in California so wasn't late.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: FurryNutz on August 14, 2018, 06:25:08 AM
I think we can all agree that the poor extender is bricked and needs to be replaced. LOL.  ::)
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 14, 2018, 09:35:32 AM
I think we can all agree that the poor extender is bricked and needs to be replaced. LOL.  ::)

Nah, it will just go back to sleep in the attic as I wasn't using it anyways.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: FurryNutz on August 14, 2018, 10:12:28 AM
Lets get that replaced so when and if you do need it, it will be functional.  ;)
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 14, 2018, 10:21:16 AM
I think since its a set I would have to send back router and all, I am getting lazy in my old age and that seems like a lot of work  :)
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 14, 2018, 10:35:18 AM
Our tech had the same results as you...  ::)
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 14, 2018, 10:39:51 AM
Our tech had the same results as you...  ::)

Tell him to not remove the power during a firmware upgrade, unless of course he wants to, to see if he can bring it back to life.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 14, 2018, 10:44:34 AM
He is still working on it and trying different things.  If he gets that far I will have him try it. On most devices the recovery mode will recover if power is lost during a firmware upgrade.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: FurryNutz on August 14, 2018, 10:49:02 AM
Come on, you cant' be that old. Maybe in forum years since you've been around since DIR-655 Rev A days.  :o

I presume if something happens, Greenbay and effect some form of RMA on the extender only, maybe.  ;)

I think since its a set I would have to send back router and all, I am getting lazy in my old age and that seems like a lot of work  :)
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 14, 2018, 10:59:20 AM
Went to college for what they called "Data Processing" way back when, systems were all dumb terminals connected to a mainframe
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 14, 2018, 11:00:18 AM
Tech got it working.

Try crash recovery again. He said hold in reset button (power off and then on) until it starts blinking amber and release. When he releases, the LED goes solid amber for a little bit then starts blinking amber.

Use IE 11 and go to 192.168.0.1 (not 50). This should take you to the recovery page. Downgrade to 1.01. Start it and walk away for 15 minutes. He said it took a long time but the extender eventually rebooted and got 5 green LEDs and worked.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: FurryNutz on August 14, 2018, 11:13:10 AM
My first computer I touched was a continual paper feed form dot matrix terminal with analog hand set modem that you had to dial into to get the Sysop.  ::)

Went to college for what they called "Data Processing" way back when, systems were all dumb terminals connected to a mainframe
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 14, 2018, 11:16:56 AM
At the emergency page now and uploading the initial shipping firmware
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 14, 2018, 11:19:19 AM
My first computer I touched was a continual paper feed form dot matrix terminal with analog hand set modem that you had to dial into to get the Sysop.  ::)

We had one of those in high school had to call into the regional BOCES with modem just to make them work.

I did have the keyboard controls for my Atari 2600 so I could program BASIC  ;D
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 14, 2018, 11:22:37 AM
Emergency page worked, but I still did not get my two green up arrow.  Reloading initial firmware through the main admin page (.50) and then will update to the 1.01B02 version.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 14, 2018, 11:28:43 AM
Did factory reset and now am loading it with the 1.01B02, will do another factory reset and then connect to router to try and sync them.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: FurryNutz on August 14, 2018, 11:39:13 AM
Ya I got a Atari 400. Didn't do much programming, but gaming was good. Up all night long.  ::)

My first computer I touched was a continual paper feed form dot matrix terminal with analog hand set modem that you had to dial into to get the Sysop.  ::)

We had one of those in high school had to call into the regional BOCES with modem just to make them work.

I did have the keyboard controls for my Atari 2600 so I could program BASIC  ;D
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 14, 2018, 11:44:50 AM
Results are in : I now have 5 green lights on the extender, the router sees the extender and the extender retained the password settings through the wizard setup.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 14, 2018, 11:54:47 AM
Extender has been moved upstairs, still connecting to router normally.

(Shall we try the new firmware agian  ::) )
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 14, 2018, 12:19:16 PM
Wow both of you are old!

Glad it came back to life. New firmware has been put down for good.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 14, 2018, 12:33:56 PM
Let me know when there is a new one, I am not afraid to play with new stuff ( he says while posting from his Windows Insider machine)
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: FurryNutz on August 14, 2018, 02:47:44 PM
Maybe old, however well, experienced.  ;D

Wow both of you are old!

Glad it came back to life. New firmware has been put down for good.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 23, 2018, 06:49:55 AM
Got verification today from engineers that the krack firmware for the extender is not compatible with the current firmware for the router. They will work on a new router firmware to fix this.  ::) ::) ::)
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: FurryNutz on August 23, 2018, 07:11:17 AM
Makes you wonder how they tested it?  :o

Thank you for this information.  ;)

Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on August 23, 2018, 07:26:14 AM
Makes you wonder how they tested it?  :o

If*   :-X
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: FurryNutz on August 23, 2018, 08:08:23 AM
Exactly.  ::)
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on August 23, 2018, 08:15:11 AM
No need to test something when you have Guinea Pigs available to you.

Make sure they are testing both the official firmware and the beta firmware that fixed the 2.4 GHz issue that was never made official.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: FurryNutz on August 23, 2018, 08:31:53 AM
 :o
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on October 15, 2018, 09:44:53 AM
Got new BETA firmware for the Extender to fix the KRACK issue.

ftp://FTP2.DLINK.COM/SECURITY_ADVISEMENTS/COVR-3902/REVA/COVR-1300E_REVA_FIRMWARE_PATCH_EXTENDER_v1.01B02_WPA2.zip (ftp://FTP2.DLINK.COM/SECURITY_ADVISEMENTS/COVR-3902/REVA/COVR-1300E_REVA_FIRMWARE_PATCH_EXTENDER_v1.01B02_WPA2.zip)
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on October 15, 2018, 10:47:45 AM
Sure I will give it a go
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on October 15, 2018, 10:51:45 AM
Thanks Dave.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on October 15, 2018, 11:57:06 AM
Installed new firmware and extender NOT bricked  ;D
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on October 15, 2018, 12:12:38 PM
Whoa? No way!  Does it connect to the router OK?
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: davevt31 on October 15, 2018, 12:57:36 PM
Yep, router sees it just fine.
Title: Re: COVR-3902 KRACK Firmware v1.10B11 BETA Released (Extender Only)
Post by: GreenBay42 on October 15, 2018, 01:05:36 PM
Nice. Thanks for testing.