D-Link Forums

D-Link IP Cameras for Home => DCS-936L => Topic started by: GreenBay42 on September 25, 2017, 09:13:55 AM

Title: BETA Firmware v1.04.04 (Build 3219) Released
Post by: GreenBay42 on September 25, 2017, 09:13:55 AM
New BETA firmware now available. 

Note: Seems Motion Detection is not working with this release.

Firmware --> ftp://FTP2.DLINK.COM/PRODUCTS/DCS-936L/REVA/BETA/DCS-936L_REVA_BETA_FIRMWARE_v1.04.04_3219.zip (ftp://FTP2.DLINK.COM/PRODUCTS/DCS-936L/REVA/BETA/DCS-936L_REVA_BETA_FIRMWARE_v1.04.04_3219.zip)

Release Notes:

Changes:
1. Change mydlink agent to v2.1.0-b93.

Bug Fixes:
1. DEFCON: D-link DCS-936L vulnerabilities in firmware updates and wifi configuration.
2. Find some readable information relative with password by wireshark sniffer tool.
3. Test fail with CSRF protection.
4. Motion detection is inconsistent and inaccurate, too many false positives.[HQ20170323000010-USA]
5. The packet is not encrypted when modifying admin password. [VBG17020104]
6. Motion detection and mydlink portal video display issues [HQ20161004000004-South Europe]
7. Security Test Fail - Web Server Password Transmitted Over HTTP.
8. Support NTP Specification "D-Link IPCam NTP Behavior Specification_20160606.pdf".
9. Fixed the issue that http return 417 why receive "Expect 100-continues"(send from mylink portal).
10. Change WebUI to use digest authentication, but keep nipca/mydlink related cgi with basic authentication. (Requirement from Dlink)
11. Support dlink security requirement TCP-Syn/TCP-Fin/UDP port scan (by using NMAP)

Known Issues:
1. In Setup/Image Setup, click “Reset to Default” will make the live screen become black. Refresh the page will return to normal.
2. In Setup/Motion Detection, click “Save Settings” will make the live screen become black. Refresh the page will return to normal


Title: Re: BETA Firmware v1.04.04 (Build 3219) Released
Post by: FurryNutz on September 25, 2017, 09:54:15 AM
Not one notification or motion detected after loading this. Tried using default (30%) and now at 80%. Still nothing.  :-\

Did full FW updated then factory reset and set up from scratch. Set just two detect area blocks is all where I know were someone would be seen walking and should be detected by camera.
Title: Re: BETA Firmware v1.04.04 (Build 3219) Released
Post by: GreenBay42 on September 25, 2017, 10:04:18 AM
How far away from the camera are the "trigger" points?

Is the camera behind glass pointing outside?
Title: Re: BETA Firmware v1.04.04 (Build 3219) Released
Post by: FurryNutz on September 25, 2017, 10:29:08 AM
about 18' and 25' from the camera. I can try closer points if needed.
No. Pointed inside a room.
Title: Re: BETA Firmware v1.04.04 (Build 3219) Released
Post by: FurryNutz on September 25, 2017, 11:12:26 AM
ok cleared area and set 3 new detect blocks closer to the camera, with in 10 feet. Still nothing.  :-\
Title: Re: BETA Firmware v1.04.04 (Build 3219) Released
Post by: GreenBay42 on September 25, 2017, 01:11:00 PM
Did you reset the camera after the upgrade?

Do you get anything at 100% sensitivity??

Title: Re: BETA Firmware v1.04.04 (Build 3219) Released
Post by: FurryNutz on September 25, 2017, 02:44:04 PM
Yes.

Will chk 100%.
Title: Re: BETA Firmware v1.04.04 (Build 3219) Released
Post by: GreenBay42 on September 26, 2017, 09:17:05 AM
Verified motion detection is not working. Closing this thread.
Title: Re: BETA Firmware v1.04.04 (Build 3219) Released
Post by: FurryNutz on September 26, 2017, 09:31:50 AM
 :(