• November 02, 2024, 08:24:01 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Router Internet Link Drop Off  (Read 5022 times)

manickavel.g@gmail.com

  • Level 1 Member
  • *
  • Posts: 4
Router Internet Link Drop Off
« on: November 12, 2014, 01:14:05 PM »

Hey I purchased the router recently, I am facing the same problem, and i have done every thing, but still it has an issue.  I am not sure about the FW ver.  but the FW update date is April 2011.  In addition to that, when the internet connection goes off, at that time if I connect the LAN cable to the Laptop, the internet link getting Up, and all the device able to surf.
Should I update to the newer version 1.02?
Please help to resolve this issue.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Router Internet Link Drop Off
« Reply #1 on: November 12, 2014, 01:27:05 PM »

Link>Welcome!

  • What Hardware version is your router? Look at sticker under the router case.
  • Link>What Firmware version is currently loaded? Found on the routers web page under status.
  • What region are you located?


Internet Service Provider and Modem Configurations
  • What ISP Service do you have? Cable or DSL?
  • What ISP Modem Mfr. and model # do you have?
  • Is ISP Modem/Service using Dynamic or Static WAN IP addressing?
  • What ISP Modem service link speeds UP and Down do you have?
  • Check cable between Modem and Router, swap out to be sure. Link> Cat6 is recommended.
  • Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask. Link>Checking MTU Values
  • For DSL/PPPoE connections on the router, ensure that "Always ON" option is enabled.
  • If the ISP modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>Double NAT and How NAT Works. To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged. If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ. Also check the routers DHCP IP address maybe conflicting with the ISP modems IP address of 192.168.0.1. Check to see if this is the same on the ISP modem, and if modem can't be bridged, change the DIR router to 192.168.1.1 or .0.254.
    Example of a D-Link router configured for PPPoE with ISP Modem bridged: PPPoE Configuration on Router

I recommend that you have your ISP check the cabling going to the ISP modem, check signal levels going to the ISP modem. For DSL or Fiber service lines, ensure that the ISP is using good working phone or cable lines to the DSL modem and that the phone lines are filtered correctly. For cable Internet, RG-6 coaxial cable is needed, not RG-59. Check for t.v. line splitters and remove them as they can introduce noise on the line and lower the signal going to the ISP modem. I recommend having the ISP service physically check the lines going from the out side to the ISP modem. Connecting to the ISP modem could result in a false positive as the signal to the modem could be just enough to that point then adding on a router, could see problems. The router operation is dependent upon getting good data flow from the ISP modem and the modem is dependent upon getting good signal from the ISP Service.

Router and Wired Configurations
Some things to try: - Log into the routers web page at 192.168.0.1. Use IE, Opera or FF to manage the router. Besure to log into the Admin account on the router.

  • Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual or under Setup/PARENTAL CONTROL/Set to>None: Static IP or Obtain Automatically From ISP.
  • Enable or Disable Use Unicasting (compatibility for some ISP DHCP Servers) and test under Setup/Internet/Manual. Disable may help with speed performance on higher speed ISP services.
  • Turn on DNS Relay  under Setup/Networking. Link>Finding Faster DNS Addresses using Name Bench and input new DNS addresses under Setup/Internet/Manual.
  • Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting and maintain consistency for applications that need to connect as well as mapped drives.
  • Ensure devices are set to auto obtain an IP address.
  • If IPv6 is an option on the router, select Local Connection Only under Setup/IPv6.
  • Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall. Enable or Disable SPI to test.
  • Enable uPnP and Multi-cast Streaming under Advanced/Networking. Disable uPnP for testing Port Forwarding rules. Enable IPv6 Multi-cast Streaming for routers that have a Media Server option. Disable IPv6 Multi-cast Streaming if IPv6 or Media Server is not being used.
  • Turn off WISH, and WPS under Advanced.
  • WAN Port Speed set to Auto or specific speed? Some newer ISP modems support 1000Mb so manually setting to Gb speeds can be supported by the router. Advanced/Advanced Networking/WAN Port Speed
  • Set current Time Zone, Date and Time. Use an NTP Server feature. The DST setting is only needed in the NA region. Tools/Time.

 

Wireless Configurations
Links>Wireless Installation Considerations and Managing Signal Congestion and Good Neighbour Policy
  • Ensure the default (dlink) SSID name is changed. Can be anything and not something that's already in use by any neighboring WiFi routers. Under Setup/Wireless/Manual.
  • What wireless modes are you using?
  • 2.4Ghz Routers only: Try single mode G or N or mixed G and N?
  • Channel Width set for Auto 20/40Mhz or try 20Mhz only.
  • Try setting a manual Channel to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear. 13 for EU regions.
  • What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES, so you might want to try TPIK only or Auto TPIK and AES.
  • What wireless devices do you have connected?
  • Ensure any devices with WiFi adapter drivers are updated.
  • Any 2.4Ghz or 5Ghz cordless house phones or WiFi APs near by?
  • Any other WiFi routers in the area? Link> Use InSSIDer to find out. How many? Use v3, its free.
  • If you have any of these options, Try turning OFF or ON Short GI, WLAN Partition, Extra Wireless Protection and HT 20/40 Co-existence if you have it. Also testing with HT20/40Mhz Co-existence enabled will impact results as well. I prefer to use this option OFF. Recommended settings are default. Under Advanced/Advanced Wireless.

Router Placement
Forum User - "Well I feel really dumb. After moving the router away from other electronic devices my speeds are back to normal. Just a heads up for anyone experiencing slow speeds, you might want to move it away from other electronics and see if that helps."
3-6' feet minimum safe distance between devices.
Placement on main level floor and central in the building and WELL ventilated is preferred. Not in basements or closets as building materials, or near by electronics devices could interfere or hinder good signal propagation.
http://www.smallnetbuilder.com/wireless/wireless-basics/31083-smallnetbuilders-wireless-faq-the-essentials


Hey I purchased the router recently, I am facing the same problem, and i have done every thing, but still it has an issue.  I am not sure about the FW ver.  but the FW update date is April 2011.  In addition to that, when the internet connection goes off, at that time if I connect the LAN cable to the Laptop, the internet link getting Up, and all the device able to surf.
Should I update to the newer version 1.02?
Please help to resolve this issue.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.