• March 28, 2024, 11:24:40 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Pages: 1 [2]

Author Topic: DIR-885L KRACK Firmware v1.21B03 BETA Released  (Read 26017 times)

zlobo

  • Level 1 Member
  • *
  • Posts: 6
Re: DIR-885L KRACK Firmware v1.21B03 BETA Released
« Reply #15 on: September 27, 2020, 03:07:51 AM »

Upgraded to this version, and now a fjew days after it started to lose 6 pings and then it runs fo 1-5min and same hapens agin.
During the ping loses router is unavail "router not found".

i will try to roll back
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DIR-885L KRACK Firmware v1.21B03 BETA Released
« Reply #16 on: September 27, 2020, 09:55:54 AM »

Did you try a full factory reset of the router after v1.21 FW was applied and setup from scratch?

Upgraded to this version, and now a fjew days after it started to lose 6 pings and then it runs fo 1-5min and same hapens agin.
During the ping loses router is unavail "router not found".

i will try to roll back
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

zlobo

  • Level 1 Member
  • *
  • Posts: 6
Re: DIR-885L KRACK Firmware v1.21B03 BETA Released
« Reply #17 on: September 28, 2020, 12:33:08 AM »

Did you try a full factory reset of the router after v1.21 FW was applied and setup from scratch?

Upgraded to this version, and now a fjew days after it started to lose 6 pings and then it runs fo 1-5min and same hapens agin.
During the ping loses router is unavail "router not found".

i will try to roll back

Did a factory reset and it acts the same, went back to 1.20 and it's still acting the same. i think i managed to kill the router  :-\ . if you don't have any other ideas that i can try?

Edit Disconnected everything from the router and it seems that my covr-2202 is causing the issue. Thats strange since its not running in router mode.
« Last Edit: September 28, 2020, 09:35:56 AM by zlobo »
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DIR-885L KRACK Firmware v1.21B03 BETA Released
« Reply #18 on: September 28, 2020, 05:54:15 PM »

How is the COVR connected to the 885? Is the COVR in AP or router mode?
Is both 885 and COVR wireless running at the same time?
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

zlobo

  • Level 1 Member
  • *
  • Posts: 6
Re: DIR-885L KRACK Firmware v1.21B03 BETA Released
« Reply #19 on: October 01, 2020, 04:57:29 AM »

How is the COVR connected to the 885? Is the COVR in AP or router mode?
Is both 885 and COVR wireless running at the same time?

its connected in bridge mode, and only 2,4Ghz is enabled on the 885 but its using a different ssid and running on different channel.
also the cover uses 1gbit backhaul.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DIR-885L KRACK Firmware v1.21B03 BETA Released
« Reply #20 on: October 01, 2020, 07:16:14 AM »

How close is the DIR router to the A Point? Distance wise...
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

zlobo

  • Level 1 Member
  • *
  • Posts: 6
Re: DIR-885L KRACK Firmware v1.21B03 BETA Released
« Reply #21 on: October 02, 2020, 01:25:01 AM »

i would say first one about 13 meters away from the router. second one is in the garage also about 13 meters away in the opposite  direction .
i use fw1.06 on the cover-2202 and they use wired backhaul.

reason for why the 2,4Ghz is on on the router is that the vacuum cleaner does not support 5Ghz and 2,4Ghz with same ssid for some reason.
I recently bought the Cover to get coverage in the garage an in the garden.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DIR-885L KRACK Firmware v1.21B03 BETA Released
« Reply #22 on: October 02, 2020, 07:17:08 AM »

Ok, well you can do this, set manual channels on the DIR router to something far apart from what the COVR uses. Since we can't change channels on COVR. Use a wifi analyzer to see what channels the COVR is using and then change the DIR router to something far apart. 1, 6 or 11.

I would turn down the power output of the DIR router as well. Try medium or low. Helps reduce the interference and noise for the COVR wifi. I do this when I'm testing two wifi systems at the same time. If your using the COVR more as your primary wifi system, then the DIRs wifi doesn't need to be working as much.  ;)
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.
Pages: 1 [2]