Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[RPMCGB]

I have looked in so many places and am turning to this forum for help with a  few D-Link issues we have.

Should I be getting 300mbps (potential) from the DAP-1320?  It works great but we constantly check and are only seeing 144mbps.

Thanks

[FurryNutz]

Link>Welcome!

• What Hardware version is your router? Look at sticker under router.
• Link>What Firmware version is currently loaded? Found on the routers web page under status.
• What region are you located?

Are your connecting client device and main host router HW supporting of 300Mb? Please refer to the devices Mfr support site for help and information regarding that.

Wireless Configurations on main host router
Links>Wireless Installation Considerations and Managing Signal Congestion and Good Neighbour Policy

• Ensure the default (dlink) SSID name is changed. Can be anything and not something that's already in use by any neighboring WiFi routers. Under Setup/Wireless/Manual.
• What wireless modes are you using?
• 2.4Ghz Routers only: Try single mode G or N or mixed G and N?
• Channel Width set for Auto 20/40Mhz or try 20Mhz only.
• Try setting a manual Channel to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear.
• What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES, so you might want to try TPIK only or Auto TPIK and AES.
• What wireless devices do you have connected?
• Any 2.4Ghz or 5Ghz cordless house phones or WiFi APs near by?
• Any other WiFi routers in the area? Link> Use InSSIDer to find out. How many?
• If you have any of these options, Try turning OFF or ON Short GI, WLAN Partition, Extra Wireless Protection and HT 20/40 Co-existence if you have it.

http://forums.dlink.com/index.php?topic=1236.0

[RPMCGB]

What Hardware version is your router? Router is currently DIR-645 Hardware is A1
What Firmware version is currently loaded? 1.01
What region are you located? Southern Ontario canada
Are you wired or wireless connected to the router?  Wireless
Wireless N mode
Also I am PC based on Outlook Express & Internet Explorer


Will try other items that apply in reply, thanks.

[FurryNutz]

What FW is loaded on the DAP?

[RPMCGB]

Now that I've got my DIR-826L going, the DAP-1320 will not work with it.  It worked great with the DIR-645, we were just looking to maximize speed if possible with it.

I completed the WPS set-up on the 1320 with the 826L and the light is solid green, but I cannot hook up to it?  I can see it in my wifi manager, just can't connect to it.  It should be noted that prior to syncing it with the 826L I could at least connect to it, but not get any web access whatsoever.  Any thoughts?

Hardware on it is A1
Firmware is 1.00

[FurryNutz]

I would disable WPS on the router. Setup normal SSID name for the main host router, single mode N, WPA2/AES only and manual channel 11 if nobody else is using it near by. Then do a factory reset on the DAP and connect to the DAP with a PC or Laptop and use the DAPs wizard to connect to the DIR-826L...

You are several revs behind on FW. If the above fails, I recommend that you update FW on the DAP using the following and try that procedure again after the last factory reset after the FW loads:
FW Update Process

[RPMCGB]

Before I saw this post I went into it a bit further and tried the WPS set-up again.  Again no luck despite the "solid green light".  I couldn't get into the DAP-1320 set-up either. I tried the windows wifi manager and nothing and went into my other wifi manager and first changed the security designation to WPA2 which let me put in the factory default password for the 1320 and it worked.

Would I still be wise to disable the WPS on the router and update the firmware or should I leave well enough alone?

Side note: getting better Mbps on the 1320 now, if that makes any sense whatsoever...

Now I am hoping to turn the 645 into an access point from the 826L to get decent full coverage in all areas.  Also going to hard wire the 826L to my main system as I've already went to the hassle of running the 75' of cable.

[FurryNutz]

I'd test with WPS disabled and manually connect the DAP to the SSID instead.

You can use the 645 as a wired AP:
Turning a router into an AP.

[RPMCGB]

Thanks! x2

[FurryNutz]

Keep us posted... 

[RPMCGB]

I saw the DAP-1320 increased in speed as it was...only since I turned the 645 into an AP (for upstairs) wired to the 826L, my coverage is insane!  I unplugged the DAP-1320 and will use it again I'm sure.  Thanks for the insight once again!!

I have one more question but I will post in another area.

[FurryNutz]

Enjoy.