• December 09, 2021, 06:05:40 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: dap-1320 blinking light  (Read 12183 times)

stwilson17

  • Level 1 Member
  • *
  • Posts: 3
dap-1320 blinking light
« on: January 28, 2016, 06:08:04 PM »

Since I reset my DAP-1320 to factory settings it won't go steady green.
This has been going on for about three hours. It is about four or five years old. Is it's time up?
Any help or suggestions will be greatly appreciated.
Thanks

Hardware version A1
Firmware version 1.00
Region: United States
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49868
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: dap-1320 blinking light
« Reply #1 on: February 02, 2016, 07:42:57 AM »

Any status on this?  ???

Can you connect to the DAP with a wired PC to it's web page?
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

stwilson17

  • Level 1 Member
  • *
  • Posts: 3
Re: dap-1320 blinking light
« Reply #2 on: February 02, 2016, 07:53:15 AM »

No. It does not go solid green.  When I try to log to Dap webpage, reads page not found or it times out. Http://dlinkap.local does not work on none of my browsers
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49868
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: dap-1320 blinking light
« Reply #3 on: February 02, 2016, 07:54:45 AM »

When you do a factory reset on the DAP you need to connect the DAP to a PC directly and set a Static IP address on the PC to 192.168.0.49 and subnet mask to 255.255.255.0 then try to connect to the DAPs web page at 192.168.0.50.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

stwilson17

  • Level 1 Member
  • *
  • Posts: 3
Re: dap-1320 blinking light
« Reply #4 on: February 02, 2016, 10:41:32 AM »

OK  I was able to connect. Thanks for the assist!
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49868
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: dap-1320 blinking light (RESOLVED)
« Reply #5 on: February 02, 2016, 10:53:29 AM »

Enjoy.  ;)
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

jlmoriart

  • Level 1 Member
  • *
  • Posts: 1
Re: dap-1320 blinking light
« Reply #6 on: July 21, 2021, 08:45:14 AM »

Sorry to necro this thread but I figured I'd share. I couldn't connect to http://dlinkap.local when connected to the device's own wifi network on my Ubuntu 20.04 laptop, but I was able to from my Galaxy S9+ android phone. From there I could go through the set up process, connecting the range extender to my home network and getting it working again. So if anyone has issues connecting after a factory reset, try another device or two maybe? Good luck internet friends.

Model: DAP-1320A1
Logged