• March 28, 2024, 11:32:27 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: DIR-880L Wired Connection Drops every few minutes  (Read 4752 times)

jbator

  • Level 1 Member
  • *
  • Posts: 1
DIR-880L Wired Connection Drops every few minutes
« on: February 09, 2015, 07:14:01 PM »

Hello;

I have a hardwired computer that drops connection every few minutes, doesn't matter what I'm doing. I notice the red x in the network box.  I have 50mbps cable service from shaw connected to a new HP desktop. I've run through all the tests from HP to no avail. Can anyone suggest a fix? I've swapped network cables and ports, hard booted the router several times and have the latest firmware. Thanks,
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DIR-880L Wired Connection Drops every few minutes
« Reply #1 on: February 10, 2015, 07:28:14 AM »

Link>Welcome!

  • Link>What Firmware version is currently loaded? Found on the routers web page under status.
  • What region are you located?

Internet Service Provider and Modem Configurations
  • What ISP Service do you have? Cable or DSL?
  • What ISP Modem Mfr. and model # do you have?
  • Is ISP Modem/Service using Dynamic or Static WAN IP addressing?
  • What ISP Modem service link speeds UP and Down do you have?
  • Check cable between Modem and Router, swap out to be sure. Link> Cat6 is recommended.
  • Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask. Link>Checking MTU Values
  • For DSL/PPPoE connections on the router, ensure that "Always ON" option is enabled.
  • If the ISP modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>Double NAT and How NAT Works. To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged. If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ. Also check the routers DHCP IP address maybe conflicting with the ISP modems IP address of 192.168.0.1. Check to see if this is the same on the ISP modem, and if modem can't be bridged, change the DIR router to 192.168.1.1 or .0.254.
    Example of a D-Link router configured for PPPoE with ISP Modem bridged: PPPoE Configuration on a Router

Router and Wired Configurations
Some things to try: - Log into the routers web page at 192.168.0.1. Use IE, Opera or FF to manage the router. Besure to log into the Admin account on the router.
  • Turn off TrueGigaBit Routing under Setup/Internet/Manual for those routers that have this feature for testing.
  • Turn off ALL QoS or Disable Traffic Shaping (DIR only) GameFuel (DGL only and if ON.) options, Advanced/QoS or Gamefuel. For the DGL-5500, review this for Streamboost information and settings: Furry's DGL-5500 Review
  • Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual or under Setup/PARENTAL CONTROL/Set to>None: Static IP or Obtain Automatically From ISP.
  • Enable or Disable Use Unicasting (compatibility for some ISP DHCP Servers) and test under Setup/Internet/Manual. Disable may help with speed performance on higher speed ISP services.
  • Turn on DNS Relay  under Setup/Networking. Link>Finding Faster DNS Addresses using Name Bench and input new DNS addresses under Setup/Internet/Manual.
  • Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting and maintain consistency for applications that need to connect as well as mapped drives.
  • Ensure devices are set to auto obtain an IP address.
  • WAN Port Speed set to Auto or specific speed? Some newer ISP modems support 1000Mb so manually setting to Gb speeds can be supported by the router. Advanced/Advanced Networking/WAN Port Speed
  • Ensure any devices with WiFi or LAN adapter drivers are updated.

Router Placement
Forum User - "Well I feel really dumb. After moving the router away from other electronic devices my speeds are back to normal. Just a heads up for anyone experiencing slow speeds, you might want to move it away from other electronics and see if that helps."
3-6' feet minimum safe distance between devices.
Placement on main level floor and central in the building and WELL ventilated is preferred. Not in basements or closets as building materials, or near by electronics devices could interfere or hinder good signal propagation.
http://www.smallnetbuilder.com/wireless/wireless-basics/31083-smallnetbuilders-wireless-faq-the-essentials

PC 3rd Party Security Software Configurations
  • Turn off all anti virus and firewall programs on PC while testing. 3rd party firewalls are not generally needed when using routers as they are effective on blocking malicious inbound traffic.
  • Turn off all devices accept for one wired LAN PC while testing.
  • Disable any downloading client software managers, i.e. Torrents or similar.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DIR-880L Wired Connection Drops every few minutes
« Reply #2 on: February 18, 2015, 10:42:25 AM »

Any status on this?  ???

Hello;

I have a hardwired computer that drops connection every few minutes, doesn't matter what I'm doing. I notice the red x in the network box.  I have 50mbps cable service from shaw connected to a new HP desktop. I've run through all the tests from HP to no avail. Can anyone suggest a fix? I've swapped network cables and ports, hard booted the router several times and have the latest firmware. Thanks,
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.