• April 15, 2024, 11:29:30 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Loaded 1.34NA but router shows 1.32NA version  (Read 3620 times)

MrGST

  • Level 1 Member
  • *
  • Posts: 15
Loaded 1.34NA but router shows 1.32NA version
« on: May 31, 2010, 05:30:51 PM »
Hi...
First question, I just updated the firmware from 1.32NA to 1.34NA but the router still shows 1.32NA as being installed. The update process goes fine without errors. Any ideas?

Thanks!
Logged

Cobra

  • Level 4 Member
  • ****
  • Posts: 477
Re: Loaded 1.34NA but router shows 1.32NA version
« Reply #1 on: May 31, 2010, 06:07:27 PM »
Lots of threads about this.

Push the reset button on the back of the router until all the lights flash.

Wait for router to fully initialize then flash firmware again.
Logged

MrGST

  • Level 1 Member
  • *
  • Posts: 15
Re: Loaded 1.34NA but router shows 1.32NA version
« Reply #2 on: May 31, 2010, 06:09:38 PM »
Thanks. I did try searching but didn't find anything. What search criteria can you recommend so I can find some of those posts?
Logged

MrGST

  • Level 1 Member
  • *
  • Posts: 15
Re: Loaded 1.34NA but router shows 1.32NA version
« Reply #3 on: May 31, 2010, 06:24:25 PM »
Btw...I just followed your advice and successfully updated the router. Thanks!

I'd still like to know what to search on because I'm still not coming up with any results...
Logged

Cobra

  • Level 4 Member
  • ****
  • Posts: 477
Re: Loaded 1.34NA but router shows 1.32NA version
« Reply #4 on: May 31, 2010, 06:33:15 PM »
Click advanced search and select the DIR655 forum only to search.

Search the word update.
Logged

MrGST

  • Level 1 Member
  • *
  • Posts: 15
Re: Loaded 1.34NA but router shows 1.32NA version
« Reply #5 on: May 31, 2010, 07:11:56 PM »
It took me a few minutes to figure out how to show / select the individual forums in Advanced Search...but once I figured it out, I was able to search and find results. Thanks!

ps. I'm really NOT an idiot, LOL. :-)
Logged

Mackerel

  • Level 3 Member
  • ***
  • Posts: 348
Re: Loaded 1.34NA but router shows 1.32NA version
« Reply #6 on: May 31, 2010, 10:02:43 PM »
Quote from: MrGST on May 31, 2010, 07:11:56 PM
ps. I'm really NOT an *****, LOL. :-)

Nobody said you were... We all have been there; experience you build from scratch...
Logged

thekochs

  • Level 2 Member
  • **
  • Posts: 27
Re: Loaded 1.34NA but router shows 1.32NA version
« Reply #7 on: June 01, 2010, 07:20:26 AM »
Quote from: Cobra on May 31, 2010, 06:07:27 PM
Push the reset button on the back of the router until all the lights flash.
Wait for router to fully initialize then flash firmware again.

So, I guess there is a difference in quick push of the RESET versus longer push/hold ?
I assume one is quick reset where config/firmware revision stays and other resets to initial defaults/firmware ?

Thx.
Logged

MrGST

  • Level 1 Member
  • *
  • Posts: 15
Re: Loaded 1.34NA but router shows 1.32NA version
« Reply #8 on: June 01, 2010, 09:21:55 AM »
Apparently. Before I joined the forum, I attempted to reset/reinstall but it didn't work. After holding the button in for about 15 seconds, all (or most, I think two on the left didn't) blinked and the new firmware installed correctly.
Logged