• August 14, 2018, 08:20:14 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: 5009 is only device on my network that won't reconnect  (Read 773 times)

caraM

  • Level 2 Member
  • **
  • Posts: 44
5009 is only device on my network that won't reconnect
« on: April 29, 2018, 10:48:43 AM »

Is there a setting in the management screens for the 5009 that tells the camera to try to reconnect if a network drops?  I just installed a new router, had to take things offline and back on a number of times -- and every other device (Swann and another DLink camera, Brother printer, etc.) -- reconnected to the network after it was back up.  Not the 5009.  Had to power it down and back up again each time.  PITA.  Is there a setting I can adjust?
Logged
DCS-5009L with firmware v1.06.02
DIR-882 with fw current as of 4/28/18

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 45425
  • D-Link Global Forum Moderator
    • New DIR-890L Router with SmartConnect™ Technology
Re: 5009 is only device on my network that won't reconnect
« Reply #1 on: April 29, 2018, 11:46:20 AM »

Try setting up a static IP addresss ON the camera instead of using a DHCP IP address. Set the routers IP pool for 192.168.100 to .200.
Then you use use any IP address out side of this pool for static IPs set ON devices. You can use 192.168.0.1 of course.
Logged
Cable:200mb/10Mb>Motorola MB7420>COVR3902>HP 24pt Gb Switch. 3xDGL-4500s,DIR-857,835,827,815,890L,880L,868L,865L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting

caraM

  • Level 2 Member
  • **
  • Posts: 44
Re: 5009 is only device on my network that won't reconnect
« Reply #2 on: April 29, 2018, 02:16:28 PM »

Thanks - already have been doing that.  All devices that are connected most of the time (not sporadically, like our phones and laptops and televisions) are on static IPs.  And anything I may want to connect to from outside my network is on static.  So the 5009 is and has been on a static IP.
Logged
DCS-5009L with firmware v1.06.02
DIR-882 with fw current as of 4/28/18

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 45425
  • D-Link Global Forum Moderator
    • New DIR-890L Router with SmartConnect™ Technology
Re: 5009 is only device on my network that won't reconnect
« Reply #3 on: April 29, 2018, 02:26:58 PM »

Might try a factory reset then set up from scratch again with the new router and see.
Logged
Cable:200mb/10Mb>Motorola MB7420>COVR3902>HP 24pt Gb Switch. 3xDGL-4500s,DIR-857,835,827,815,890L,880L,868L,865L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting