• March 18, 2024, 10:55:33 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: DWL-2600AP Rev A - Firmware - Official Release - v4.2.0.13  (Read 16137 times)

GreenBay42

  • Administrator
  • Level 11 Member
  • *
  • Posts: 2752
DWL-2600AP Rev A - Firmware - Official Release - v4.2.0.13
« on: April 02, 2018, 08:45:23 AM »

Firmware version 4.2.0.13 released.

Firmware - ftp://FTP2.DLINK.COM/PRODUCTS/DWL-2600AP/REVA/DWL-2600AP_REVA_FIRMWARE_v4.2.0.13.zip

Release Notes:

New Features:

1. Supports Wireless ARP suppression mode support in standalone mode

Issues Fixed:

1. WPA2 KRACK vulnerability patch
2. Fix LLC frames from client's MAC address appear on LAN port even if client is not yet really connected to the network. [DEUR20160224000004]
3. Fix E-mail notification is blocked by ALG-enabled firewall. [DUSA20160412000001]
4. Fix the vulnerability the PKCS7_dataDecodefunction in crypto/pkcs7/pk7_doit.c in OpenSSL before 0.9.8zg, 1.0.0 before 1.0.0s, 1.0.1 before 1.0.1n, and 1.0.2 before 1.0.2b allows remote attackers to cause a denial of service (NULL pointer dereference and application crash) via a PKCS#7 blob that uses ASN.1 encoding and lacks inner EncryptedContent data. [CVE-2015-1790]
5. Fix OpenSSL vulnerability CMS verify infinite loop with unknown hash function. [CVE-2015-1792]
6. Fix integer overflow in the EVP_EncryptUpdate function in crypto/evp/evp_enc.c in OpenSSL before 1.0.1t and 1.0.2 before 1.0.2h allows remote attackers to cause a denial of service (heap memory corruption) via a large amount of data. [CVE-2016-2106]
7. Fix time is not updated when Daylight Saving Time is enabled.
8. Fix time is still changed even system is not in Daylight Saving Time period or the countries which don’t have Daylight Saving Time.
9. Fix with maximum of 32 characters not able to login to AP to enable debug logs.
10. Fix existing GUI session is not expired after changing password from CLI.
11. Fix existing SSH session is not expired after disabling the SSH service.
12. [CLI] Fix no check for maximum limit for the Read-write community name Field in SNMP settings page.
13. Fix device time is not updated correctly for North Korea and South Korea Time zones.
14. Fix in SNMP page Hostname field is accepting 252 Characters where max limit is 253 and the Error should be proper when multicast ip is configured in IPV4
address field.
15. Fix the offset value is not proper on date and time setting page.
16. Fix Http Certificate Expiration Date is not update properly when AP date is set after 2017.
17. Fix valid error message was not shown after configuring invalid Broadcast Key Refresh Rate in VAP page.
18. Fix AP is accepting invalid IP address in "Hostname, address, or subnet of Network Management System field" of SNMP page.
19. [CLI] Fix no validation for Broadcast/Multicast IP addresses for Management ACL when configured from CLI.
20. Fix SNMP help content regarding the maximum users that can be added in the SNMPv3 user page is not available.
21. Fix proper error message is not displaying after configuring invalid session Key Refresh Rate in VAP page.
22. Unable to configure the maximum characters for Community name for traps and Host name or IP Address in SNMP page.
23. Fix device is accepting multicast mac address in packet capture configuration.
24. Fix spell mistake in help page of client QOS ACL page.
25. Fix AP is not sending disassociation packet when radio is changes to OFF state

Known Issues:

1. GUI access might be slow.
2. Sometimes WDS Link cannot be established in managed mode.
3. Some extra field of radio2 are present in DWL 2600AP’s help content.
4. Sometimes we cannot see "Operation Succeed" message on the GUI pages after clicking on the save button
5. Observed more than 10 continual ping loss while doing fping to internet IP 8.8.8.8 for establishing WDS link.
6. Observed null (zero) values while running the iperf traffic from LAN to WLAN in both the radio (2.4 GHz and 5 Ghz).
7. Power LED is not blinking properly when AP is rebooted from GUI or CLI.
8. Observed 10 continual ping loss to internet (8.8.8.8) in long duration test for the radio 2.4GHz with the security WPA personal(TKIP)
Logged