• March 29, 2024, 03:56:33 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: DSR-1000N L2TP over IPSEC works with Windows but doesn't with iOS and Android  (Read 8058 times)

mmiat

  • Level 1 Member
  • *
  • Posts: 4

I configured L2TP over IPSEC and it works fine with Windows XP and Windows 7
but when I try to connect with mobile devices I have this log:

Code: [Select]
Wed Oct 02 12:17:18 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  an undead schedule has been deleted: 'pk_recvupdate'.
Wed Oct 02 12:17:18 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  Sending Informational Exchange: delete payload[]
Wed Oct 02 12:17:14 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  IPsec-SA established[UDP encap 4500->4500]: ESP/Transport 88.36.202.90->94.163.120.254 with spi=139308332(0x84dad2c)
Wed Oct 02 12:17:14 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  IPsec-SA established[UDP encap 4500->4500]: ESP/Transport 94.163.120.254->88.36.202.90 with spi=93459421(0x59213dd)
Wed Oct 02 12:17:14 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  Adjusting peer's encmode 4(4)->Transport(2)
Wed Oct 02 12:17:14 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  No policy found, adjusting source address for generating the policy incase of NAT-T in Transport Mode: 94.163.120.254/32[0] 88.36.202.90/32[1701] proto=udp dir=in
Wed Oct 02 12:17:14 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  No policy found, generating the policy : 1.194.143.206/32[0] 88.36.202.90/32[1701] proto=udp dir=in
Wed Oct 02 12:17:14 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  Using IPsec SA configuration: anonymous
Wed Oct 02 12:17:14 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  Responding to new phase 2 negotiation: 88.36.202.90[0]<=>94.163.120.254[0]
Wed Oct 02 12:17:13 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  ISAKMP-SA established for 88.36.202.90[4500]-94.163.120.254[4500] with spi:cb24c1b7c94a1a6e:1b4359ec551c93fe
Wed Oct 02 12:17:13 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  KA found: 88.36.202.90[4500]->94.163.120.254[4500] (in_use=2)
Wed Oct 02 12:17:13 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  Floating ports for NAT-T with peer 94.163.120.254[4500]
Wed Oct 02 12:17:13 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  NAT detected: PEER
Wed Oct 02 12:17:13 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  NAT-D payload does not match for 94.163.120.254[500]
Wed Oct 02 12:17:13 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  NAT-D payload matches for 88.36.202.90[500]
Wed Oct 02 12:17:13 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  For 94.163.120.254[500], Selected NAT-T version: RFC 3947
Wed Oct 02 12:17:13 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  Received Vendor ID: DPD
Wed Oct 02 12:17:13 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  Received unknown Vendor ID
Wed Oct 02 12:17:13 2013 (GMT +0200): [DSR-1000N] [IKE] INFO:  Received unknown Vendor ID

in DSR I see, in Status > Active VPNs > device is present with "IPsec SA Established" state, but the device isn't connect and it shows me "operation not succeed"
DSR-1000N info: Hardware Version: A1 - Firmware Version: 1.08B51_WW
thanks for any help
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting

You'll need to phone contact your local or regional DLink support office for help for this device.

Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

mmiat

  • Level 1 Member
  • *
  • Posts: 4

done, but they didn't help me. They only sent me some pdf and a beta firmware...
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting

What region are you located?
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

mmiat

  • Level 1 Member
  • *
  • Posts: 4

Italy
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting

I recommend that you phone contact them back once more and tell them that this didn't work and see if they can review your router configuration or see if getting you a RMA for the 1000 for a new one. Ask them to test this set up there before they send you a new one.

Ensure your iOS and Android are tested as well. Any new updates to these devices. Had this ever been working at all?

Is this router being used at a home or business?
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.