• March 28, 2024, 02:58:29 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: 655 REV B-Problems Just my two cents here  (Read 4205 times)

Mr. Ptarmigan

  • Level 1 Member
  • *
  • Posts: 1
655 REV B-Problems Just my two cents here
« on: March 10, 2018, 07:03:40 PM »

Just my two cents here, there has been a lot of response scattered over all websites' forums about this particular router. (DIR-655 rev B1)

I decided to try and bring this old router to life but it has been very troublesome. I will try to give my advice based on my latest attempt seeming to be the best configuration so far..

My first advice is to accept that trying to configure this old router is like trying to learn advanced skills, so it is probably easier to get a newer router and just go with DD-WRT..(DD-WRT is very tricky to install yourself but works great and can be expensive to find pre-installed)

Okay, I have Comcast 15/2 speed with SB6121 modem and no problems until I switched to this old router..
But, since I want to learn, I have spent so much time tinkering with and will share the results here.

I updated to the latest firmware 2.11NA and have since performed two factory resets since the wireless always seems to start failing. (Apple devices, specifically)
-(All wired devices working great included those hooked to second Netgear router configured as an Access Point.)

SO FAR: Here are my settings in router firmware-
SETUP> INTERNET> click Manual Internet Connection Setup > uncheck "Enable Advanced DNS Service"

SETUP> WIRELESS SETTINGS> click Manual Wireless Connection Setup>
(Okay, here is where I am leaving default settings unchanged to fix MY wireless problem)>
(wireless password was already created from router initial setup,
mixed 802.11n g AND b,
wireless channel will depend on you,
trans. rate "auto",
Ch. width 20 Mhz,
visibility status "visible",
security mode "WPA personal",
WPA mode "WPA Only",
cypher type "TKIP and AES")


Router firmware settings continued-
SETUP> NETWORK SETTINGS> uncheck "Enable DNS Relay"

DHCP reservations (SETUP> NETWORK SETTINGS> DHCP RESERVATIONS LIST) helped connect my old MacBook but not my iPhone 4s iOS 6.1.3 >>> Once I performed another router factory reset and opted not to change the wireless settings, my iPhone and everything seems to connect just fine.

Under ADVANCED> QOS ENGINE> leave Traffic Shaping turned off by default

Under ADVANCED> ADVANCED WIRELESS> I have not changed anything here yet, but I want to disable "WMM" and "short GI" and probably turn down the transmit power (turning WMM "off" is questionable since Apple says just leave it on. https://support.apple.com/en-us/HT202068)

Under ADVANCED> WISH> I do not wish to use Microsoft anymore and don't see any need to enable this (my idea is to turn off most things to make a functional router of this)

Under ADVANCED> turn off WPS (WiFi Protected Setup) will make more secure

So that's it so far, I still need to apply future changes one at a time and wait to see if any issues with wireless. I assume anybody still trying to use this router won't be looking to tap into top speeds so maybe stick with wireless mixed mode 802.11b/g/n even though only have wireless n devices.

I'll admit I like this router, but only if I can get it to work. I much prefer the layout of DD-WRT!

UPDATE: It seems the extra factory resets helped! All wireless connections still good, and I changed each setting one by one until finally I have 802.11n only, with "AUTO: WPA/WPA2 with AES" security. I tried performing a "hard" reset a couple times, so, not sure if it did anything, but it goes a little further than just pressing for ten seconds. Just look up 30-30-30 hard reset method, usually used with 3rd-party custom firmware.
« Last Edit: March 11, 2018, 01:52:37 AM by Mr. Ptarmigan »
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: 655 REV B-Problems Just my two cents here
« Reply #1 on: March 11, 2018, 11:07:41 AM »

Link>Welcome!

  • What region are you located?

Last time I used this router, about two years ago, it was stable and working well.

I presume that this maybe a configuration issue is all. This router was a work horse and solid router to use.

Please try some of the suggestions here:
Router Troubleshooting Suggestions and Tips

I recommend using single mode N or if you have devices that need G mode, mixed G and N.
If you have older devices then you'll need WPA and TPIK. If you don't, then try using WPA2 and AES only.
Manual channel 1, 6 or 11 is recommended instead of auto.
If you have older devices, 20Mhz maybe needed. If not, use AUTO for channel width.

You can disable Short GI and test. WMM should always be enabled for best speed performances on wifi.

WISH is for All wireless devices, not just MS.

D-Link routers do not support 30-30-30 reset methods. 10 seconds on the back button or the Reset to Factory in the UI is all that's needed for D-Link routers.
This model router does not support 3rd party or GPL FW due to it's closed proprietary chip set.
There is v2.12 FW available for models in the NA region.

« Last Edit: May 01, 2018, 12:28:49 PM by FurryNutz »
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: 655 REV B-Problems Just my two cents here (RESOLVED)
« Reply #2 on: May 01, 2018, 12:29:09 PM »

Glad you got it working better. Enjoy.
 ;)
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.