• March 28, 2024, 10:45:46 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: V1.04 - After upgrade from V1.03, Printserver not working  (Read 4104 times)

Banshee1971

  • Level 3 Member
  • ***
  • Posts: 105
V1.04 - After upgrade from V1.03, Printserver not working
« on: February 03, 2008, 10:51:57 AM »

I notice 2 strange thing after i upgrade the DNS-323.
1 - Printserver not working (i re-map my printer under my laptop who have winXP, and under my desktop who have Vista).
2 - The DNS name seem not working under Vista. But still working unde WinXP.

Here a list of what i done :
- I reset the DNS to factory default, and reinstall manually the config (recreate every thing, username,..)
- I clear the print queue
- I disconnect the printer (power down) and reconnect
- I shutdown the NAS and restart
- I manually enter the DNS name into my router (Linksys with DD-WRT code on it)
- The DNS name still working under WinXP (i can ping the name and get the IP resolved), but it's not working under vista
- My NAS still have the same NAME and IP since V1.03
- I successfully map the NAS under Vista only with IP name (net use x: \\192.168.x.x\Volume_1\my_folder_name /username:theusername password)
- I successfully map the NAS under WinXP using IP or DNS (replace the 192.168  with the DNS name).

My printer are a cheap DELL Laserjet 1100 printer.... it's a very basic printer, nothing else.

is there something to fixe this ?  first, fix the printer issue, and later, fix the DNS issue under Vista ????
Logged

Banshee1971

  • Level 3 Member
  • ***
  • Posts: 105
Re: V1.04 - After upgrade from V1.03, Printserver not working
« Reply #1 on: February 03, 2008, 01:17:07 PM »


Good news... if i downgrade to v1.03, everything i lost start working again :
- DNS name working, so i can MAP using the DNS name
- PrintServer working.


So, V1.04 broke the printserver and the DNS
Logged

Banshee1971

  • Level 3 Member
  • ***
  • Posts: 105
Re: V1.04 - After upgrade from V1.03, Printserver not working
« Reply #2 on: February 07, 2008, 01:23:40 PM »

I think this problems will stay there for a while ...

In case i did'nt tell, i test the "clear print job" ... and also restet to factory default without fix the problems.
Logged

fordem

  • Level 10 Member
  • *****
  • Posts: 2168
Re: V1.04 - After upgrade from V1.03, Printserver not working
« Reply #3 on: February 07, 2008, 03:23:03 PM »

Banshee

What are you running as a DNS server?
Logged
RAID1 is for disk redundancy - NOT data backup - don't confuse the two.

Banshee1971

  • Level 3 Member
  • ***
  • Posts: 105
Re: V1.04 - After upgrade from V1.03, Printserver not working
« Reply #4 on: February 07, 2008, 03:53:36 PM »


Linksys WRT-54GS V4 and WRT-54GL V1.1 (i try both) with DD-WRT23SP2 firmware on it.


note : lost the DNS name are not an issue for me, but it was nice to have it before lost it. Lost the printer are an issue
Logged