• March 28, 2024, 02:05:23 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Pages: 1 ... 3 4 [5] 6

Author Topic: DIR-882-US FORUM USER REQUESTS and BUGS  (Read 51849 times)

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DIR-882-US FORUM USER REQUESTS and BUGS
« Reply #60 on: December 16, 2019, 12:14:59 AM »

Well this maybe a HW issue or a FW issue. However I don't think it's a FW issue. Last time I had my 882 online, it worked fully for me an my near 30 devices. I have about same number of 5Ghz devices.

You might revert back to a prior version of FW and see. You'll need to use the recovery mode to downgrade:
Emergency Recovery Mode

Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

jope76

  • Level 1 Member
  • *
  • Posts: 1
Re: DIR-882-US FORUM USER REQUESTS and BUGS
« Reply #61 on: December 16, 2019, 12:46:02 AM »

Hi,

I have two problems with the 1.2 firmware that has made me revert back to the 1.11 firmware:

1) The admin web page has problems with Safari on iOS. The page works ok the first visit and login, bur after that I just eget a blank page each visit. If I clear all cached web data in Safari I can log in again. This problem is not present with the 1.11 firmware.

2) D-Link has updated the channel list in 1.2, and it now includes the U-NII-3 channels for my country (sweden). This makes the Auto channel mode select these channels, and two of my clients can no longer connect since they don't support U-NII-3. This forces me to make a manual channel selection to one of the regular U-NII-1 channels. Firmware 1.11 did not include U-NII-3 channels, so I could run Auto channel selection without any problems.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DIR-882-US FORUM USER REQUESTS and BUGS
« Reply #62 on: December 16, 2019, 12:57:58 AM »

Had you done a factory reset and setup from scratch after v1.20 was applied?

What iOS version are you using?
Be sure you are using FW code from your regional D-Link web site.

I would make contact with our regional D-Link support office and let them know what your seeing.
Link> Tech Support Contact Information

Hi,

I have two problems with the 1.2 firmware that has made me revert back to the 1.11 firmware:

1) The admin web page has problems with Safari on iOS. The page works ok the first visit and login, bur after that I just eget a blank page each visit. If I clear all cached web data in Safari I can log in again. This problem is not present with the 1.11 firmware.

2) D-Link has updated the channel list in 1.2, and it now includes the U-NII-3 channels for my country (sweden). This makes the Auto channel mode select these channels, and two of my clients can no longer connect since they don't support U-NII-3. This forces me to make a manual channel selection to one of the regular U-NII-1 channels. Firmware 1.11 did not include U-NII-3 channels, so I could run Auto channel selection without any problems.
« Last Edit: December 16, 2019, 01:02:38 AM by FurryNutz »
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

all_or_nothing

  • Level 1 Member
  • *
  • Posts: 11
Re: DIR-882-US FORUM USER REQUESTS and BUGS
« Reply #63 on: December 28, 2019, 05:11:39 AM »

Also, i more thing i observed is it can't handle more than 4-5 connected devices in 5G. It's beam forming technology latches on to one of the devices and cuts off network access to everything. I had to specially enable 2.4G for devices which are not able to connect over 5G because of this. But usually i have observed there will be only 4 devices on 5G, other all would be connected over 2.4G. This problem exists across all firmware versions. Same observation with Smart Connect enabled and disabled. All my devices are 802.11ac 5G capable. Is there any workaround this problem?
same problem here, FW 1.2, just few device is connected with 5GHz.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DIR-882-US FORUM USER REQUESTS and BUGS
« Reply #64 on: December 29, 2019, 11:32:35 AM »

Link>Welcome!

  • What region are you located?

Has you done a factory reset and setup from scratch after v1.20 was applied?


same problem here, FW 1.2, just few device is connected with 5GHz.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DIR-882-US FORUM USER REQUESTS and BUGS
« Reply #65 on: December 29, 2019, 03:29:28 PM »

Ok, I put my 882 online today and connected several 5Ghz supporting devices to it. I first disabled 2.4Ghz and SC and just 5Ghz enabled.

One PC was connected with a DWA-192 and a laptop was connected to a NetGear R7800 in wireless bridge mode.

I then enabled 2.4Ghz and SC. All devices re-connected and got internet access with out problems.

Router FW v1.20
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

all_or_nothing

  • Level 1 Member
  • *
  • Posts: 11
Re: DIR-882-US FORUM USER REQUESTS and BUGS
« Reply #66 on: December 30, 2019, 06:11:00 AM »

ok, i fix this isue. there is some problem with network card, channel for use in wireless mode is under 12 in europe or something.
https://imgur.com/a/WnXtFEV
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DIR-882-US FORUM USER REQUESTS and BUGS (RESOLVED)
« Reply #67 on: December 30, 2019, 10:35:04 AM »

Well that tells the adapter to work on wireless mode G N and AC. I presume there is other selections for that drop down.

What was the other selections?

As far as channels go, for 2.4Ghz 1 thru 11 here in the USA, for Europe regions, 1 thru 13 is supported.

Sounds like you got it figured out.

Enjoy.  ;)

ok, i fix this isue. there is some problem with network card, channel for use in wireless mode is under 12 in europe or something.
https://imgur.com/a/WnXtFEV
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

all_or_nothing

  • Level 1 Member
  • *
  • Posts: 11
Re: DIR-882-US FORUM USER REQUESTS and BUGS
« Reply #68 on: January 02, 2020, 02:31:03 AM »

https://imgur.com/a/UKAvxsr
ok,
10-11 on wireless mode settings is workig,
11-11 and 12-11 is not. i have no idea why.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DIR-882-US FORUM USER REQUESTS and BUGS
« Reply #69 on: January 02, 2020, 11:02:58 AM »

Something to ask Qualcomm about.

https://imgur.com/a/UKAvxsr
ok,
10-11 on wireless mode settings is workig,
11-11 and 12-11 is not. i have no idea why.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

sachb

  • Level 1 Member
  • *
  • Posts: 14
Re: DIR-882-US FORUM USER REQUESTS and BUGS
« Reply #70 on: April 18, 2020, 10:53:12 AM »

Feature Request such as :

1) Option to choose security as WPA2 AES, instead of WPA/WPA2.

2)Instead of Auto 20/40/80 MHZ, it would be much better if Dlink gives us the option to choose it individually like 80 mhz or combine only 20/40 MHZ together for 5 ghz & 2.4 ghz band.

3)  Connected device's Link speed.
Logged

kriskate

  • Level 1 Member
  • *
  • Posts: 1
Re: DIR-882-US FORUM USER REQUESTS and BUGS
« Reply #71 on: August 08, 2020, 01:19:25 PM »

I've unfortunatelly upgraded to 1.30 and the usb ports can't even read a 32gb usb-stick, although the power indicator on the stick lights up.

Furthermore, after the (previous) firmware merged the two wi-fi networks (2.5GHz and 5GHz), the signal has weakened, and where (behind 3 walls) I had a speedtest of ±100 mbps, now it even disconnects the laptop from the wi-fi network.
Laptop still reports full signal connection on 5ghz, but after for example a youtube video buffer, it just disconnects. Happens on two macbook pros (2015 and 2020).

Anyone else had similar issues?.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DIR-882-US FORUM USER REQUESTS and BUGS
« Reply #72 on: August 08, 2020, 02:22:44 PM »

Do you factory reset the router after updating FW?


I've unfortunatelly upgraded to 1.30 and the usb ports can't even read a 32gb usb-stick, although the power indicator on the stick lights up.

Furthermore, after the (previous) firmware merged the two wi-fi networks (2.5GHz and 5GHz), the signal has weakened, and where (behind 3 walls) I had a speedtest of ±100 mbps, now it even disconnects the laptop from the wi-fi network.
Laptop still reports full signal connection on 5ghz, but after for example a youtube video buffer, it just disconnects. Happens on two macbook pros (2015 and 2020).

Anyone else had similar issues?.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

all_or_nothing

  • Level 1 Member
  • *
  • Posts: 11
Re: DIR-882-US FORUM USER REQUESTS and BUGS
« Reply #73 on: August 09, 2020, 02:15:42 AM »

1.3 is not working for me.
factory default, then update through router own updater, factory defaul and give this:

reconect every 2 minutes.
after this, emergency recovery is broken, so update failed all the times, no matter which browser or 30-30-30 procedure i use.
fortunately, original web gui is load, then revert to 1.2 and everything is sucessfuly restored.

dont fix what is not broken  :)
« Last Edit: August 09, 2020, 08:15:57 AM by FurryNutz »
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: DIR-882-US FORUM USER REQUESTS and BUGS
« Reply #74 on: August 09, 2020, 08:17:18 AM »

Try loading the v1.30 from a downloaded file and apply using a wired PC and web browser.
http://forums.dlink.com/index.php?topic=75671.0

Be sure your getting the file for your region as well.


1.3 is not working for me.
factory default, then update through router own updater, factory defaul and give this:

reconect every 2 minutes.
after this, emergency recovery is broken, so update failed all the times, no matter which browser or 30-30-30 procedure i use.
fortunately, original web gui is load, then revert to 1.2 and everything is sucessfuly restored.

dont fix what is not broken  :)
« Last Edit: August 09, 2020, 08:19:02 AM by FurryNutz »
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.
Pages: 1 ... 3 4 [5] 6