• May 21, 2024, 05:46:40 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Block Incoming Traffic  (Read 7010 times)

agrafil

  • Level 1 Member
  • *
  • Posts: 1
Block Incoming Traffic
« on: June 23, 2011, 08:46:36 AM »

Hi,

I need to block incoming traffic with Dlink DIR 600. I know how to create the rule source (WAN) to destination (LAN)  to deny all protocols. But what IP will I put in WAN? IP address of my Internet? Or how can I enter the ALL IP range in source...format for the IP (it's not 0.0.0.0).

I want to do this because in the DIR log section I'm being PING Flooded.  I already un-check "Enable WAN Ping Response" but still receiving the message.

Thanks in advance.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Block Incoming Traffic
« Reply #1 on: June 24, 2011, 11:37:39 AM »

I think you would put in the ip address being reported in the logs where the pings are coming from.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

altair_xms

  • Level 2 Member
  • **
  • Posts: 63
Re: Block Incoming Traffic
« Reply #2 on: June 25, 2011, 02:43:24 AM »

just curious what is the version of your firmware (below 2.06?)

why?...i notified same issue when i use uTorrent (ping flooding attack) when i have installed 2.05 (and bellow), i guess dir600 wrongly detect as ping flooding traffic from uTorrent (download on computer was ok).

Later i installed 2.06 (not because of above mentioned reason), looking in tab "Status" i never seen "Ping floding attack"...i presume D-link "fixed" (one of) bugs....?!
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Block Incoming Traffic
« Reply #3 on: June 28, 2011, 12:23:47 PM »

It's possible the pings are being mistaken for an attack. Have you set up any inbound rules for uTorrent and the ports it's using? Might help this here.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

altair_xms

  • Level 2 Member
  • **
  • Posts: 63
Re: Block Incoming Traffic
« Reply #4 on: July 01, 2011, 11:12:02 PM »

i didn't set any explicit rules...from the beginning when i bought router uTorrent worked fine.

i have set MAC filter on for my PC & laptop + DHCP with IP's for those two machines
Logged