• March 29, 2024, 07:51:58 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: [Help] Realtime VBR  (Read 5212 times)

Somat

  • Level 1 Member
  • *
  • Posts: 1
[Help] Realtime VBR
« on: April 10, 2013, 11:31:36 AM »

i got dlink dsl-2640b...now i use default config (UBR without PCR) but get too much data losses/lagging when i play online games on ipad  ???...can i know which set up ATM PVC for online games that need nearest stable incoming/outgoing data transfer ? or like Real Time VBR ? erm...do i need to set up Port Triggering?? or just ignore that and play forever a noob  ;D
Thanks in advance...


Please Help meh
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: [Help] Realtime VBR
« Reply #1 on: June 24, 2013, 07:49:43 AM »

Link>Welcome!
  • What Hardware version is your router? Look at sticker under router.
  • Link>What Firmware version is currently loaded? Found on routers web page under status.
  • What region are you located?
  • Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask. Link>Checking MTU Values
  • For DSL/PPPoE connections on the router, ensure that "Always ON" option is enabled.

Router and Wired Configurations
Some things to try: - Log into the routers web page at 192.168.0.1. Use IE, Opera or FF to manage the router.

  • Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting.
  • Ensure devices are set to auto obtain an IP address.
  • Check cable between Modem and Router, swap out to be sure. Link> Cat6 is recommended.

Wireless Configurations
Links>Wireless Installation Considerations and Managing Signal Congestion
  • Ensure the default (dlink) SSID name is changed. Can be anything and not something thats already in use by any neighboring WiFi routers. Under Setup/Wireless/Manual.
  • What wireless modes are you using?
  • 2.4Ghz Routers only: Try single mode G or N or mixed G and N?
  • Channel Width set for Auto 20/40Mhz or try 20Mhz only.
  • Try setting a manual Channel to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear.
  • What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES, so you might want to try TPIK only or Auto TPIK and AES.
  • What wireless devices do you have connected?
  • Any cordless house phones?
  • Any other WiFi routers in the area? Link> Use InSSIDer to find out. How many?
  • If you have any of theese options, Try turning OFF or ON Short GI, WLAN Partition, HT 20/40 Co-exhistance and Extra Wireless Protection if you have it. Recommended settings are default. Under Advanced/Advanced Wireless.
  • Enable WMM Enable Under Advanced/Advanced Wireless.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.