The Graveyard - Products No Longer Supported > DIR-601

New DIR-601 Rev B Only v2.01 Released

<< < (2/3) > >>

FurryNutz:
Link>Welcome!
What Hardware version is your router? Look at sticker under router.
Link>What Firmware version is currently loaded? Found on routers web page under status.
What region are you located?
Are you wired or wireless connected to the router?
Has a Factory Reset been performed?

What ISP Service do you have? Cable or DSL?
What ISP Modem Mfr. and model # do you have?

Does you new ISP email require TLA/TLS security on there email system? if so, then this is the cause of the router not being able to send out emails as these routers don't support this security I believe. I ran into this issue on other model routers after my ISP service switched to Googles back end email system and they require this TLA/TLS security system. Thats when email notifications stopped working for me.

You may need to set up a virtual server option for your teamspeak application.



--- Quote from: KeBeKeR on April 11, 2013, 12:21:06 PM ---Email Notification dont work whathever the schedule is and only port 25 work!! and major isp block this port and why give a option to change the port if only port 25 work !!! with my other isp i was able to sent email cuz port 25 was working but neva send on scejule or at full log and now my new isp block port 25.....that foction never work at this time...

Blocked incoming TCP Ack packet all the time n spi is needed for security my teamspeak server member got allways disconect cuz of that.....

dir-601 revb 2.01na >:(



--- End quote ---

KeBeKeR:
dir-601 rev b 2.01na im wired i was dsl now cable my isp is videotron

several time

factory reset
dont work
flash new fw dont work (factory reset each time after flash)

change isp after

several time

factory reset
dont work
flash new fw dont work (factory reset each time after flash)

for mail i try hotmail yahoo google videotron electronicbox whathever the mail account still dont work

and portfoward is done with ts server and i use ddns adress but still got Blocked incoming TCP Ack packet for range off good adress of member and they got disconect time out or unable to connect i had to reset several time befor the Blocked incoming TCP Ack packet stop !!!!!!!!! i had to reset often and its boring !!!

FurryNutz:
What ISP Modem Mfr. and model # do you have?

Does your new ISP email require TLA/TLS security on there email system? What kind of security do they require? This maybe a compatibility issue of the email system your ISP is using and these routers.

Like i said before, My ISP was working using the old port 25 email, however since they changed to Google, and they require TLA/TLS security authentication, I don't think DLink router support this option.

KeBeKeR:
Arris Tm722g Cable Modem Docsis 3.0 


and @videotron.ca mail work on port 25 but the router still dont send on scejul or on full log ....in log if i send manually that work but neva on schejule day or week or full log or whathever the setting is.


and Blocked incoming TCP Ack packet is a realy big problem

FurryNutz:
Some things to try: - Log into the routers web page at 192.168.0.1. Use IE, Opera or FF to manage the router.
Turn off ALL QoS or Disable Traffic Shaping (DIR only) GameFuel (DGL only and if ON.) options. Advanced/QoS or Gamefuel.
Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual or under Setup/PARENTAL CONTROL/Set to>None: Static IP or Obtain Automatically From ISP.
Enable Use Unicasting (compatibility for some ISP DHCP Servers) under Setup/Internet/Manual.
Turn on DNS Relay under Setup/Networking.
Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting.
Ensure devices are set to auto obtain an IP address.
If IPv6 is an option on the router, select Local Connection Only or Disable IPv6 options under Setup/IPv6.
Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall.
Enable uPnP and Multi-cast Streaming under Advanced/Networking. Disable uPnP for testing Port Forwarding rules. Disable IPv6 Multi-cast Streaming if IPv6 is not being used.
Turn off WISH, and WPS under Advanced.

Set current Time Zone, Date and Time. Use an NTP server feature. Tools/Time.

You might try using ISP DNS intially while you attempt to get Teamspeak going. Then if you can get it going, then switch to DDNS.

You can try this as well"
Finding Faster DNS Addresses using Name Bench

If the logs are getting sent manually, then i would check the scheduling to make sure the settings are correct and proper. Do a test schedule and set up something to see if anything gets sent at that time. If not, there could be an issue with FW.  :-\

FYI:
Arris Cable Modems and External Routers

Navigation

[0] Message Index

[#] Next page

[*] Previous page