• April 24, 2024, 05:40:06 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: wireless network not in range  (Read 11956 times)

oachi

  • Level 1 Member
  • *
  • Posts: 1
wireless network not in range
« on: September 01, 2012, 09:38:30 AM »

Hello,

I don't know why, but suddenly, my wireless network is not in range for my PC.....
My tablet and my TV are connected wireless to the internet, through DIR 600, but my computer cannot see anymore my wireless network. I can see other wireless networks, from neighbors, but mine is not listed.
If I connect my PC through a cable,I have internet access, but wireless is not working anymore...
Any help is highly appreciated!

Thank you and best regards,
O.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: wireless network not in range
« Reply #1 on: September 01, 2012, 09:59:37 AM »

Link>Welcome!
What Hardware version is your router? Look at sticker under router.
Link>What Firmware version is currently loaded? Found on routers web page under status.
What region are you located?
Are you wired or wireless connected to the router?

What ISP Service do you have? Cable or DSL?
What ISP Modem do you have? Stand Alone or built in router?
What ISP Modem make and model do you have?

Some things to try: - Log into the routers web page at 192.168.0.1.
Turn off ALL QoS or Disable Traffic Shaping (DIR only) GameFuel (DGL only and if ON.) options. Advanced/QoS or Gamefuel.
Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual.
Turn on DNS Relay under Setup/Networking.
Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking
Ensure devices are set to auto obtain an IP address.
Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall.
Enable uPnP and Multi-cast Streaming under Advanced/Networking.

Link>Wireless Installation Considerations
What wireless modes are you using? Under Setup/Wireless/Manual.
Try single mode G or N or mixed G and N?
Channel Width set for Auto 20/40Mhz or try 20Mhz only.
Try setting a manual channel to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear.
What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES, so you might want to try TPIK only or Auto.
What wireless devices do you have connected?
Any cordless house phones?
Any other WiFi routers in the area? Link> Use InSSIDer to find out. How many?

Turn off WISH, and WPS under Advanced.
Try turning off Short GI, WLAN Partition,and Extra Wireless Protection if you have it. Under Advanced/Advanced Wireless.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: wireless network not in range
« Reply #2 on: October 03, 2012, 09:43:48 AM »

Any status on this?
Any of the suggestions help?
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.