• March 28, 2024, 09:10:21 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: dwl8610ap keeps rebooting  (Read 6493 times)

nair

  • Level 1 Member
  • *
  • Posts: 1
dwl8610ap keeps rebooting
« on: November 21, 2020, 09:25:17 AM »

Hi,
We have about 60 APs (DWL8610AP), and till now, we have 4 AP that keeps rebooting, I tried to log using the console to inspect the problem, but couldn't know what to do.
In the following the log of the console if anyone can help.

---------------------------
Rebooting in 5 seconds..
==================== CFE Boot Loader ====================
c_ddr_init: sdram_config=0x014b sdram_ncdl=0x00000190
c_ddr_init: DDR PLL locked
Decompressing...done
Found chip type NAI (0x3f00cf12)
Chipc: rev 42, caps 0x48000a, chipst 0x0 pmurev 0, pmucaps 0x0
Found a ST compatible (Marconix) serial flash with 32 64KB blocks; total size 2MB
si_kattach done. ccrev = 42, wd_msticks = 125000


CFE version 6.30.163.2002 (r382208 BCMINT) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Enterprise UAP Version 1.3.2
ALPHA CFE v1.00r004
Build Date: Thu Dec  5 18:34:59 CST 2013 (jack@108)
Copyright (C) 2000-2013 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 524288(0x80000)
config_cs0 = 0x25142200
acc_control_cs0 = 0xd7010010
new acc_control_cs0 = 0xd7050010
Found a AMD NAND flash:
Total size:  128MB
Block size:  128KB
Page Size:   2048B
OOB Size:    64B
Sector size: 512B
Spare size:  16B
ECC level:   5-bit
Device ID: 0x01 0xf1 0x80 0x1d 0x01
R_REG(cs_nand_select)   = 0x60000101
R_REG(config_cs0)   = 0x25142200
R_REG(acc_control_cs0)   = 0xd7050010
DDR Clock: 400 MHz
Warning: using legacy sdram_ncdl parameter to set DDR frequency. Equivalent setting in clkfreq=1000,*533* will be ignored.
si_doattach: incoming bus is PCI but it's a lie, switching to SI devid:0x4715
Found chip type NAI (0x3f00cf12)
Chipc: rev 42, caps 0x48000a, chipst 0x0 pmurev 0, pmucaps 0x0
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.2002 (r382208 BCMINT)
si_doattach: incoming bus is PCI but it's a lie, switching to SI devid:0x4715
Found chip type NAI (0x3f00cf12)
Chipc: rev 42, caps 0x48000a, chipst 0x0 pmurev 0, pmucaps 0x0
et1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.2002 (r382208 BCMINT)
si_doattach: incoming bus is PCI but it's a lie, switching to SI devid:0x4715
Found chip type NAI (0x3f00cf12)
Chipc: rev 42, caps 0x48000a, chipst 0x0 pmurev 0, pmucaps 0x0
et2: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.2002 (r382208 BCMINT)
si_doattach: incoming bus is PCI but it's a lie, switching to SI devid:0x4715
Found chip type NAI (0x3f00cf12)
Chipc: rev 42, caps 0x48000a, chipst 0x0 pmurev 0, pmucaps 0x0
et3: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.2002 (r382208 BCMINT)
CPU type 0x0: 1000MHz
Tot mem: 524288 KBytes

CFE mem:    0x00F00000 - 0x010C8890 (1869968)
Data:       0x00F6F8B4 - 0x00F70F30 (5756)
BSS:        0x00F70F40 - 0x00FC6890 (350544)
Heap:       0x00FC6890 - 0x010C6890 (1048576)
Stack:      0x010C6890 - 0x010C8890 (8192)
Text:       0x00F00000 - 0x00F5CA1C (379420)
Boot:       0x010C9000 - 0x01109000
Reloc:      I:00000000 - D:00000000

GPIO-00 = 0
GPIO-00 enabled as an output
GPIO-01 = 0
GPIO-01 enabled as an output
Invalid interface IP address: 192.168.1.1

Booting Image 1 ...
kernel_args: console=ttyS0,115200 ubi.mtd=5 root=ubi0:rootfs ro rootflags=sync rootfstype=ubifs user_debug=31
Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: ... 2422804 bytes read
Entry at 0x00008000
Starting program at 0x00008000
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.36.4brcmarm+ (root@localhost.localdomain) (gcc version 4.5.3 (Buildroot 2012.02) ) #1 SMP PREEMPT Mon Jun 29 08:12:49 EDT 2015
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: Northstar Prototype
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writealloc
MPCORE found at 19020000
PERCPU: Embedded 7 pages/cpu @c1926000 s4512 r8192 d15968 u65536
pcpu-alloc: s4512 r8192 d15968 u65536 alloc=16*4096
pcpu-alloc:
  • 0
  • 1

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125952
Kernel command line: console=ttyS0,115200 root=ubi0:rootfs rootfstype=ubifs ro rootflags=sync user_debug=31
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB 384MB = 512MB total
Memory: 514760k/514760k available, 9528k reserved, 393216K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xf7e00000 - 0xffe00000   ( 128 MB)
    vmalloc : 0xc8800000 - 0xf0000000   ( 632 MB)
    lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .init : 0xc0008000 - 0xc004d000   ( 276 kB)
      .text : 0xc004d000 - 0xc048c000   (4348 kB)
      .data : 0xc04aa000 - 0xc04ce6e0   ( 146 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
   RCU-based detection of stalled CPUs is disabled.
   Verbose stalled-CPUs detection is disabled.
NR_IRQS:256
MPCORE GIC init
MPCORE Global Timer Clock 500000000Hz
Calibrating delay loop... 1998.84 BogoMIPS (lpj=9994240)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
MPCORE Private timer setup CPU0
Calibrating local timer... 499.714MHz.
L310: cache controller enabled 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x7a130000
CPU1: Booted secondary processor
MPCORE Private timer setup CPU1
Brought up 2 CPUs
SMP: Total of 2 processors activated (3991.14 BogoMIPS).
devtmpfs: initialized
atomic64 test passed
NET: Registered protocol family 16
Found a ST compatible (Marconix) serial flash with 64 64KB blocks; total size 4MB
NVRAM kernel_args: console=ttyS0,115200 ubi.mtd=5 root=ubi0:rootfs ro rootflags=sync rootfstype=ubifs user_debug=31
CCA UART Clock Config: Sel=1 Ovr=1 Div=48
CCA UART Clock rate 125000000Hz
bio: create slab <bio-0> at 0
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource mpcore_gtimer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 49152 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: no core
PCI: no core
PCI: scanning bus 0
PCI: Fixing up bus 0
PCIE1 link=1
PCIE1 switching to GEN2
PCIE1 link=1
PCI: Fixing up bus 0
PCI: bus0: Fast back to back transfers disabled
PCI: Fixing up bus 1
PCI: bus1: Fast back to back transfers disabled
pci 0001:00:00.0: BAR 8: assigned [mem 0x08000000-0x080fffff]
pci 0001:01:00.0: BAR 0: assigned [mem 0x08000000-0x08003fff 64bit]
pci 0001:01:00.0: BAR 0: set to [mem 0x08000000-0x08003fff 64bit] (PCI address [0x8000000-0x8003fff]
pci 0001:00:00.0: PCI bridge to [bus 01-01]
pci 0001:00:00.0:   bridge window [io  disabled]
pci 0001:00:00.0:   bridge window [mem 0x08000000-0x080fffff]
pci 0001:00:00.0:   bridge window [mem pref disabled]
PCIE2 link=1
PCIE2 switching to GEN2
PCIE2 link=1
PCI: Fixing up bus 0
PCI: bus0: Fast back to back transfers disabled
PCI: Fixing up bus 2
PCI: bus2: Fast back to back transfers disabled
pci 0002:00:00.0: BAR 8: assigned [mem 0x40000000-0x402fffff]
pci 0002:02:00.0: BAR 2: assigned [mem 0x40000000-0x401fffff 64bit]
pci 0002:02:00.0: BAR 2: set to [mem 0x40000000-0x401fffff 64bit] (PCI address [0x40000000-0x401fffff]
pci 0002:02:00.0: BAR 0: assigned [mem 0x40200000-0x40207fff 64bit]
pci 0002:02:00.0: BAR 0: set to [mem 0x40200000-0x40207fff 64bit] (PCI address [0x40200000-0x40207fff]
pci 0002:00:00.0: PCI bridge to [bus 02-03]
pci 0002:00:00.0:   bridge window [io  disabled]
pci 0002:00:00.0:   bridge window [mem 0x40000000-0x402fffff]
pci 0002:00:00.0:   bridge window [mem pref disabled]
PCIE3 link=0
Reset Button GPIO = 4
Leds Driver Version 1.0
highmem bounce pool size: 64 pages
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering unionfs 2.5.11 (for 2.6.36.4)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 237
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18000300 (irq = 117) is a 16550
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
brd: module loaded
loop: module loaded
pflash: found no supported devices
Boot partition size = 524288(0x80000)
Creating 4 MTD partitions on "bcmsflash":
0x000000000000-0x000000080000 : "boot"
0x000000080000-0x0000000a0000 : "nvram"
0x0000000a0000-0x0000000c0000 : "boot_env"
0x0000000c0000-0x000000100000 : "log"
Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
Found a AMD NAND flash:
Total size:  128MB
Block size:  128KB
Page Size:   2048B
OOB Size:    64B
Sector size: 512B
Spare size:  16B
ECC level:   5-bit
Device ID: 0x 1 0xf1 0x80 0x1d 0x 1
NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD NAND 128MiB 3,3V 8-bit)
Spare area=64 eccbytes 36, ecc bytes located at:
 7 8 9 10 11 12 13 14 15 23 24 25 26 27 28 29 30 31 39 40 41 42 43 44 45 46 47 55 56 57 58 59 60 61 62 63
Available 27 bytes at (off,len):
(1,6) (16,7) (32,7) (48,7) (0,0) (0,0) (0,0) (0,0)
Scanning device for bad blocks
Bad eraseblock 188 at 0x000001780000
Bad eraseblock 210 at 0x000001a40000
Bad eraseblock 213 at 0x000001aa0000
Bad eraseblock 221 at 0x000001ba0000
Bad eraseblock 259 at 0x000002060000
Bad eraseblock 277 at 0x0000022a0000
Bad eraseblock 290 at 0x000002440000
Bad eraseblock 304 at 0x000002600000
Bad eraseblock 307 at 0x000002660000
Bad eraseblock 311 at 0x0000026e0000
Bad eraseblock 313 at 0x000002720000

Options: NO_AUTOINCR,NO_READRDY,BBT_SCAN2NDPAGE,
lookup_nflash_rootfs_offset: offset = 0x0
brcmnand: ubifs with lzo found at block #20 offset 280000
lookup_nflash_rootfs_offset: offset = 0x2800000
brcmnand: ubifs with lzo found at block #339 offset 2a60000
Creating 5 MTD partitions on "brcmnand":
0x000000000000-0x000002800000 : "linux"
0x000000280000-0x000002800000 : "rootfs"
0x000002800000-0x000005000000 : "linux2"
0x000002a60000-0x000005000000 : "rootfs2"
0x000005000000-0x000008000000 : "jffs2"
UBI: attaching mtd5 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 176:0, read 64 bytes
UBI error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 185:0, read 64 bytes
UBI error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 186:0, read 64 bytes
UBI error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 198:0, read 64 bytes
UBI error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 204:0, read 64 bytes
UBI error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 218:0, read 64 bytes
UBI error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 224:0, read 64 bytes
UBI error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 225:0, read 64 bytes
UBI error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 226:0, read 64 bytes
UBI error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 256:0, read 64 bytes
UBI error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 268:0, read 64 bytes
UBI error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 272:0, read 64 bytes
UBI error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 274:0, read 64 bytes
UBI error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 282:0, read 64 bytes
UBI warning: check_what_we_have: 15 PEBs are corrupted

corrupted PEBs are: 176 185 186 198 204 218 224 225 226 256 268 272 274 276 282
UBI error: check_what_we_have: too many corrupted PEBs, refusing this device
UBI error: ubi_init: cannot attach mtd5
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (8043 buckets, 32172 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
lib80211: common routines for IEEE802.11 drivers
Registering the dns_resolver key type
UBIFS error (pid 1): ubifs_get_sb: cannot open "ubi0:rootfs", error -19
VFS: Cannot open root device "ubi0:rootfs" or unknown-block(0,255)
Please append a correct "root=" boot option; here are the available partitions:
1f00             512 mtdblock0 (driver?)
1f01             128 mtdblock1 (driver?)
1f02             128 mtdblock2 (driver?)
1f03             256 mtdblock3 (driver?)
1f04           40960 mtdblock4 (driver?)
1f05           38400 mtdblock5 (driver?)
1f06           40960 mtdblock6 (driver?)
1f07           38528 mtdblock7 (driver?)
1f08           49152 mtdblock8 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,255)
[<c0053bf8>] (unwind_backtrace+0x0/0xe4) from [<c039a1f4>] (panic+0x68/0x188)
[<c039a1f4>] (panic+0x68/0x188) from [<c00090fc>] (mount_block_root+0x238/0x288)
[<c00090fc>] (mount_block_root+0x238/0x288) from [<c0009320>] (prepare_namespace+0x88/0x1c0)
[<c0009320>] (prepare_namespace+0x88/0x1c0) from [<c0008d70>] (kernel_init+0x1c8/0x218)
[<c0008d70>] (kernel_init+0x1c8/0x218) from [<c004ebb8>] (kernel_thread_exit+0x0/0x8)
CPU1: stopping
[<c0053bf8>] (unwind_backtrace+0x0/0xe4) from [<c004d2cc>] (do_IPI+0xd8/0x150)
[<c004d2cc>] (do_IPI+0xd8/0x150) from [<c046c108>] (__irq_svc+0x48/0xe8)
Exception stack(0xc7843f98 to 0xc7843fe0)
3f80:                                                       c04b9f44 00000000
3fa0: c7843fe0 00000000 c7842000 c04b63c0 c04cf0a8 c04cf214 00000000 413fc090
3fc0: 0000001f 00000000 c0502428 c7843fe0 c004ec10 c004ec14 60000013 ffffffff
[<c046c108>] (__irq_svc+0x48/0xe8) from [<c004ec14>] (default_idle+0x24/0x28)
[<c004ec14>] (default_idle+0x24/0x28) from [<c004ed7c>] (cpu_idle+0x40/0x94)
[<c004ed7c>] (cpu_idle+0x40/0x94) from [<00008084>] (0x8084)
Rebooting in 5 seconds..
==================== CFE Boot Loader ====================
---------------------------
Logged