D-Link Forums
D-Link Wireless Routers for Home and Small Business => DIR-882 => Topic started by: tom19693 on February 27, 2019, 11:25:59 AM
-
Model Name: DIR-882 Hardware Version: A1 Firmware Version: 1.11
Recently purchased the DIR-882 and im yet to connect to the internet using it. Im trying to connect with pppoe using all the settings my ISP provided (which work fine on 2 other routers), but im stuck with status "Limited Connection" but cannot access anything.
(https://i.imgur.com/RViuGGM.png)
Ive tried changing from static to dynamic IP which makes no difference, also tried changing a few other setting which hasn't helped. I've also factory reset and reinstalled the v1.11 firmware then factory reset again.
system log is mainly the below repeated
2018-07-03 20:13:41 [RC]: Current Wan interface is eth3 , mode is pppoe
2018-07-03 20:13:44 pppoe-relay[29132]: PADO packet from 84:26:2b:a1:ca:56 on interface eth3 does not have Relay-Session-Id tag
2018-07-03 20:13:44 pppoe-relay[29132]: PADS packet from 84:26:2b:a1:ca:56 on interface eth3 does not have Relay-Session-Id tag
2018-07-03 20:13:48 [RC]: Wan(ppp0) connect Success , Current Wan ip is xxx.xxx.xxx.xxx
2018-07-03 20:13:48 [UPNP]: WPS listening on port 8888
2018-07-03 20:13:50 [UPNP]: Can't find in which sub network the client is
2018-07-03 20:13:50 [UPNP]: Can't find in which sub network the client is
2018-07-03 20:13:52 ipsec_setup: ...Openswan IPsec stopped
2018-07-03 20:13:53 [RC]: Wan(ppp0) Disconnect
2018-07-03 20:13:53 ipsec_setup: ...Openswan IPsec stopped
2018-07-03 20:13:53 [RC]: Wan(ppp0) Disconnect
2018-07-03 20:13:53 ipsec_setup: ...Openswan IPsec stopped
2018-07-03 20:13:54 [RC]: Current Wan interface is eth3 , mode is pppoe
2018-07-03 20:13:58 pppoe-relay[8754]: PADO packet from 84:26:2b:a1:ca:56 on interface eth3 does not have Relay-Session-Id tag
2018-07-03 20:13:58 pppoe-relay[8754]: PADS packet from 84:26:2b:a1:ca:56 on interface eth3 does not have Relay-Session-Id tag
2018-07-03 20:14:02 [RC]: Wan(ppp0) connect Success , Current Wan ip is xxx.xxx.xxx.xxx
2018-07-03 20:14:02 [UPNP]: WPS listening on port 8888
2018-07-03 20:14:03 [UPNP]: Can't find in which sub network the client is
2018-07-03 20:14:04 [UPNP]: Can't find in which sub network the client is
2018-07-03 20:14:05 [UPNP]: Can't find in which sub network the client is
2018-07-03 20:14:06 ipsec_setup: ...Openswan IPsec stopped
2018-07-03 20:14:07 [RC]: Wan(ppp0) Disconnect
-
Link>Welcome! (http://forums.dlink.com/index.php?topic=49573.0)
- What Hardware version is your router? Look at sticker under the router case.
- Link>What Firmware (http://forums.dlink.com/index.php?topic=47512.0) version is currently loaded? Found on the routers web page under status.
- What region are you located?
Internet Service Provider and Modem Configurations
- What ISP Service do you have? Cable or DSL?
- What ISP Modem Mfr. and model # do you have?
- Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask. Link>Checking MTU Values (http://forums.dlink.com/index.php?topic=53008.0)
- For DSL/PPPoE connections on the router, ensure that "Always ON" option is enabled.
-
I edited out your WAN IP address. You don't need to advertise that :)
Reboot the modem. Not sure I have ever seen the limited connection status before. I will ask a tech.
-
Reboot the modem.
I've rebooted a few times. Also factory reset and reinstalled firmware.
Thanks
-
And still getting the limited connection? I have asked a few techs and they said they have never seen that status. Very strange.
Who is your ISP?
What modem do you have?
Region - UK?
-
And still getting the limited connection?
yes
Who is your ISP?
What modem do you have?
Region - UK?
Yes UK, I get openreach (BT) FTTP which comes into a ONT like the image below. (The box on the right is a battery backup)
The model name EchoLife HG8110H-20
(https://www.ispreview.co.uk/wp-content/gallery/cache/3585__500x550_fttp_ont_and_bbu_open_lid_openreach.jpg)
-
Has a LAN cable been swapped between the ONT and the 882?
Has a factory reset been performed on the 882 and setup from scratch. Walk thru the setup wizard while the router is connected to the ONT?
-
OK so I got it working.
The problem is something to do with IPv6. If i set IPv6 to 'Local Connectivity Only' everything works fine. As soon as I change the setting to anything else the internet disconnects. I'll just leave IPv6 disabled.
Thanks for the help
-
Thanks for the update and glad it worked out.
-
Do you have IPv6 support natively from your ISP?
OK so I got it working.
The problem is something to do with IPv6. If i set IPv6 to 'Local Connectivity Only' everything works fine. As soon as I change the setting to anything else the internet disconnects. I'll just leave IPv6 disabled.
Thanks for the help