D-Link Forums

The Graveyard - Products No Longer Supported => D-Link Storage => DNR-202L => Topic started by: AllynHin on January 02, 2018, 09:35:50 PM

Title: Can't Select 'Record on Event'
Post by: AllynHin on January 02, 2018, 09:35:50 PM
I've done a bit of scouring on the forums here and I was able to resolve some of my problems, the most troublesome was that I couldn't see the live image. Turns out I can only see it using IE (not firefox, not chrome, and not opera). Okay, I'll use IE for it. The problem that remains, and it's a biggie, is that I can't get this thing to record on event. The camera is set to "Enable Video Motion." In the DNR interface, in Setup>Camera-Audio and Video>CH01>Motion tab is checked for "Enable Video Motion." A field is selected and Sensitivity is set. When I go to Setup>Schedule-Recording Schedule and select the camera. It's set to "Continuous Recording". It doesn't record continuously; that's okay, I don't want it to. I click to select the radio button for "Record on Event" and click "Always" but nothing changes. In the box at the bottom of the page it shows Start/End/Record as 00:00/23:59/Continuous Recording and there's red stripes across all the lines on the calendar.

If I highlight the 00:00/23:59/Continuous Recording on the Start/End/Record box and click "Delete" it goes away, but when I select "Record on Event" and then click "Always,"  00:00/23:59/Continuous Recording reappears. If I click "Save Settings" and exit the page, when I go back, the page is the same as I left it except the radio button selected is "Continuous Recording". The only thing I see that has changed is there is an icon of a running man in the upper right corner of the live image.

The DNR 202 will record manually, but not any other way. I've cleared the browser cache more than a few times during this ordeal; didn't make a difference. Can y'all help me make this work?

Windows 10 Home 64-bit
IE 11 ver.11.125.16299.0
DNR202L:
Agent ver. 2.1.0-b61
F/W ver. 2.05.01
NVR Device Pack: 2.16.01
Camera:
DCS-5222LB
F/W ver. 2.13.01
H/W ver. B

When I started this, I had F/W ver. 2.04 on the DNR. I upgraded the firmware hoping to resolve this issue and a problem with large text overlaid on the camera image. The upgrade did not resolve either problem.

Thank you for your time.
Title: Re: Can't Select 'Record on Event'
Post by: AllynHin on January 06, 2018, 11:22:43 PM
Bump
Soo....any ideas on this?
Title: Re: Can't Select 'Record on Event'
Post by: RYAT3 on January 07, 2018, 08:17:59 AM

Do not click ALWAYS.

Click "Record on Event" radio button.

Then for each day, right click and select "Filled All".

Then Save Settings.

Everything should remain green.
Title: Re: Can't Select 'Record on Event'
Post by: FurryNutz on January 07, 2018, 11:27:12 AM
Can also try FF ESR version of there browser to see if there is any changes. This version is a special add-on supporting browser from there normal browser that no longer supports add-ons for D-Link.
Title: Re: Can't Select 'Record on Event'
Post by: AllynHin on January 08, 2018, 12:24:56 PM
Thanks so much for your replies. It simply would not do right, although last night it did inexplicably start continuous recording, which I didn't notice until this morning. I didn't mess with it last evening, so I don't know what changed overnight. I tried flashing it again and now I can get the lines to be green and the schedule indicates that it will record on event.  Whether it actually will record on event remains to be seen, but that'll be a different problem, yeah? Thanks for the help.
Title: Re: Can't Select 'Record on Event'
Post by: FurryNutz on January 08, 2018, 06:54:40 PM
Let us know how it goes...