• March 28, 2024, 05:23:30 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Pages: 1 [2]

Author Topic: Unable to access DNR-202L after firmware to v2.04  (Read 12064 times)

GreenBay42

  • Administrator
  • Level 11 Member
  • *
  • Posts: 2752
Re: Unable to access DNR-202L after firmware to v2.04
« Reply #15 on: June 13, 2017, 02:05:50 PM »

Unfortunately it sounds like it is defective. Contact tech support for options/RMA, and reference this forum post if needed.
Logged

RYAT3

  • Level 10 Member
  • *****
  • Posts: 2254
Re: Unable to access DNR-202L after firmware to v2.04
« Reply #16 on: June 13, 2017, 06:52:04 PM »

Can you ping the DNR-202L?  (Open Network Utility, click Ping. Enter the IP address of the DNR-202L and click ping).

Ping times out. However, the router does see the recorder for a brief period of time. Enough to assign it an IP address. Basically, by the time I can get terminal up to ping, the recorder emits an annoyingly loud beep and reboots. This cycles repeatedly.

My last thing I'd try - have you Tried without the USB drive?

Bamoh had issues with his dnr 202l - not being able to use a WD ultra passport drive for whatever reason.  He ended up returning his DNR202L and the next one worked.  I don't remember the symptoms he had.

I have bought 4 dnr202l, and never had a problem with a WD ultra passport drive (3 and 4TB). (I have not tried the new style you have there).  I think I got all mine from newegg. 

Oh - and the one you returned - you didn't even bother to open it?



Logged

RYAT3

  • Level 10 Member
  • *****
  • Posts: 2254
Re: Unable to access DNR-202L after firmware to v2.04
« Reply #17 on: June 13, 2017, 06:57:57 PM »


5. Tried to manually reinstall firmware using USB drive. Used
instructions on D-Link website. The process did not seem complete?

I also referenced this post:


I'm sorry you are having trouble with this process and thanks for letting me know where you are getting stuck. I seems you are releasing the scan bottom too soon... so try this...

Ensure your DNR is OFF, once you have connected the USB stick containing the new firmware with the .bin file renamed to update.bin on the HDD1 port of the DNR-202L, then follow the steps below:

1. Press and hold the SCAN button and then connect the power back to the unit. (don't let go of the SCAN button)
2. Keep holding the SCAN button until the LED ring is blinking red (this may take some time, as the unit starts up it's normal boot up sequence), you'll heard two beeps (one long and one short), keep holding the scan button until the LED ring is blinking red. Let go of the scan button (upgrade process has started)
3. Wait until you hear two short beeps (at least 3 minutes...) which means the upgrade process has ended. (LED light will be solid blue again)
4. REBOOT the unit by unplugging and reconnecting the power.

after the reboot, you will be able to find it on your network when using the latest installation wizard.

Give it a run and let us know.

That sounds like this (except this has pictures).

http://support.dlink.com/FAQView.aspx?f=ST1P9C0jMxkTqMSBvzlquA%3d%3d
Logged

RYAT3

  • Level 10 Member
  • *****
  • Posts: 2254
Re: Unable to access DNR-202L after firmware to v2.04
« Reply #18 on: June 13, 2017, 07:41:48 PM »

Post some pics of your setup. How the Dnr and router are connected.

You are able to access the router web pages?

Setup is as straight forward as possible.


Are you sure you have the right power adapters in the right devices?

Asus has used both right angle and straight.  My RT-N65R uses a straight, my newer RT-AC3200 uses a right angle.
The DNR 202L I have here uses a straight plug.  (I think we had discussion here were the DNR202L also had a right angle plug also, maybe h/w A/B revision.)

 Both of my router eletrical wires are wrapped in a single casing.  My DNR202l is not, it's in 2 separate strands combined, like the one coming out of your router, and it has white dash markings on it.  It looks like almost the same wire on each of your devices.
Logged

JChan

  • Level 1 Member
  • *
  • Posts: 10
Re: Unable to access DNR-202L after firmware to v2.04
« Reply #19 on: June 14, 2017, 08:00:09 AM »


Are you sure you have the right power adapters in the right devices?

Asus has used both right angle and straight.  My RT-N65R uses a straight, my newer RT-AC3200 uses a right angle.
The DNR 202L I have here uses a straight plug.  (I think we had discussion here were the DNR202L also had a right angle plug also, maybe h/w A/B revision.)

 Both of my router eletrical wires are wrapped in a single casing.  My DNR202l is not, it's in 2 separate strands combined, like the one coming out of your router, and it has white dash markings on it.  It looks like almost the same wire on each of your devices.

Pretty sure. The DLink adapter has it's branding on it.
Logged

JChan

  • Level 1 Member
  • *
  • Posts: 10
Re: Unable to access DNR-202L after firmware to v2.04
« Reply #20 on: June 14, 2017, 08:07:08 AM »

Can you ping the DNR-202L?  (Open Network Utility, click Ping. Enter the IP address of the DNR-202L and click ping).

Ping times out. However, the router does see the recorder for a brief period of time. Enough to assign it an IP address. Basically, by the time I can get terminal up to ping, the recorder emits an annoyingly loud beep and reboots. This cycles repeatedly.

My last thing I'd try - have you Tried without the USB drive?

Bamoh had issues with his dnr 202l - not being able to use a WD ultra passport drive for whatever reason.  He ended up returning his DNR202L and the next one worked.  I don't remember the symptoms he had.

I have bought 4 dnr202l, and never had a problem with a WD ultra passport drive (3 and 4TB). (I have not tried the new style you have there).  I think I got all mine from newegg. 

Oh - and the one you returned - you didn't even bother to open it?

I am attempting to use a Seagate drive. I have also tried a different drive (Lacie) and a USB thumb drive.

As for the one I returned, I did attempt to set it up. But after the firmware update, I encountered the same issue. After a few tries to reload the firmware, I boxed it up and returned it while I'm still within the return date.
Logged

JChan

  • Level 1 Member
  • *
  • Posts: 10
Re: Unable to access DNR-202L after firmware to v2.04
« Reply #21 on: June 14, 2017, 08:11:15 AM »


5. Tried to manually reinstall firmware using USB drive. Used
instructions on D-Link website. The process did not seem complete?

I also referenced this post:


I'm sorry you are having trouble with this process and thanks for letting me know where you are getting stuck. I seems you are releasing the scan bottom too soon... so try this...

Ensure your DNR is OFF, once you have connected the USB stick containing the new firmware with the .bin file renamed to update.bin on the HDD1 port of the DNR-202L, then follow the steps below:

1. Press and hold the SCAN button and then connect the power back to the unit. (don't let go of the SCAN button)
2. Keep holding the SCAN button until the LED ring is blinking red (this may take some time, as the unit starts up it's normal boot up sequence), you'll heard two beeps (one long and one short), keep holding the scan button until the LED ring is blinking red. Let go of the scan button (upgrade process has started)
3. Wait until you hear two short beeps (at least 3 minutes...) which means the upgrade process has ended. (LED light will be solid blue again)
4. REBOOT the unit by unplugging and reconnecting the power.

after the reboot, you will be able to find it on your network when using the latest installation wizard.

Give it a run and let us know.

That sounds like this (except this has pictures).

http://support.dlink.com/FAQView.aspx?f=ST1P9C0jMxkTqMSBvzlquA%3d%3d



Yes, that's the page I found early on. My thumb did get pretty sore after a while. I also tried to tape the button down so I don't have to hold it down for long periods of time.
Logged

GreenBay42

  • Administrator
  • Level 11 Member
  • *
  • Posts: 2752
Re: Unable to access DNR-202L after firmware to v2.04
« Reply #22 on: June 14, 2017, 08:38:14 AM »

So both units worked until you updated the firmware?

You may want to re-download the firmware file. Maybe the one you have is corrupt. I STRONGLY suggest updating the firmware via Ethernet connection. If you did it wirelessly possible data loss could have corrupted the firmware.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Unable to access DNR-202L after firmware to v2.04
« Reply #23 on: June 14, 2017, 01:10:20 PM »

Be sure to use IE11 or FF browsers for updating any FW. Disable any PC security software temporarily on LAN wired PC connected to the router. Do a factory reset on the DNR if needed, skip any set up wizards if possible, then go in and manually load the FW file, after it loads and processed, do one more factory reset then set up from scratch and use the set up wizard to set it up. Should work well.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

JChan

  • Level 1 Member
  • *
  • Posts: 10
Re: Unable to access DNR-202L after firmware to v2.04
« Reply #24 on: June 14, 2017, 02:19:52 PM »

So both units worked until you updated the firmware?

You may want to re-download the firmware file. Maybe the one you have is corrupt. I STRONGLY suggest updating the firmware via Ethernet connection. If you did it wirelessly possible data loss could have corrupted the firmware.

That's correct. Both units went out after updating the firmware. I could not access recorder via ethernet after the firmware. Both recorders were updated via ethernet connection. One was through the DLink software and the other was through the Dlink Cloud. Unfortunately, after that, I was not able to access them again. 

Thank You, everyone, for your time and effort. I gave up the battle and called D-Link Tech support. After troubleshooting over the phone, RMA has been issued and the recorder is on its way back to be repaired/refurbished.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Unable to access DNR-202L after firmware to v2.04
« Reply #25 on: June 15, 2017, 08:36:25 AM »

Be sure your using IE11 or FF when updating FW and have any PC security software disabled before sending the FW file. Follow the processes seen on the DNRs web page. Ive updated mine twice and had no issues.

Hope the RMA unit comes with v2.04 already loaded.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

RYAT3

  • Level 10 Member
  • *****
  • Posts: 2254
Re: Unable to access DNR-202L after firmware to v2.04
« Reply #26 on: June 18, 2017, 10:24:46 AM »

I just got another DNR-202L H/W A2 from Newegg and upgraded it from F/W 2.02 from 2015 to the latest 2.04.03 (July 2016) without issue in IE11 on Win7.   
This would prove the zip file online is not corrupt, and my unzip through windows explorer works fine too.

Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Unable to access DNR-202L after firmware to v2.04
« Reply #27 on: June 19, 2017, 10:22:10 AM »

Awesome, Thanks for letting us know.  ;)
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.
Pages: 1 [2]