• March 28, 2024, 12:46:18 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Replaced router, DAP-1665 no longer working  (Read 11595 times)

bkelly13

  • Level 1 Member
  • *
  • Posts: 4
Replaced router, DAP-1665 no longer working
« on: May 31, 2021, 02:22:04 PM »

Setup: Windows 10, automatic updates enabled.
Computer router: Synology RT2600. Desktop is hard wired, 2.5 and 5 Gig lights are on, Laptop and phones connect wireless.
D-Link DAP-1665, a wireless access point that worked with my previous primary router but I cannot get it to work with the Synology router/wireless adapter. In the browser I use 192.168.1.235. this is the IP found on the D-Link when connected with a cable.
The D-link normally resides in the garage connected to a solar panel monitor system.  There is only one wall between the two wireless devices.
With the D-Link on my desk less than two feet from the Synology, it connects using a cable between the two devices.  The 2.4 and 5 GHz lights on both devices are lit.
When connected with a cable, and logged on, is there a method of verifying that the 2.5 and the 5 Gig connections are functioning?  Something more substantial than a light that is on?
What must be done differently to get it working again?
Thank you for your time.

Edit: discovered that the Synology and the D-Link both have a WPS button to share account information.  Pressed the Synology button then the
D-Link button with five seconds of each other, no improvement.

Edit: using a cable, connected and set the network name and password to bad values, power cycled, and both the 2.4 and 5 Gig lights turn on.  They do not indicate a valid connection.
« Last Edit: June 01, 2021, 10:04:09 AM by bkelly13 »
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Replaced router, no longer working
« Reply #1 on: June 01, 2021, 06:46:30 AM »

Is the DAP in AP mode or extender mode?
Is the DAP connected to the host router via ethernet cable or wireless?

Try a factory reset and setup from scratch. Review the user manual and installation guide to set it up.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

bkelly13

  • Level 1 Member
  • *
  • Posts: 4
Re: Replaced router, no longer working
« Reply #2 on: June 01, 2021, 09:39:58 AM »

I have done the restart from a deep reset.

In the manual I find Access Point Mode, not using that.
Wireless Client Mode, this is what is needed.
Repeater Mode, no
Bridge Mode, no

The DAP is to reside in the garage and has done so since summer 2019, working well.
The previous router was inconsistent when using Netflix and was tossed, replaced by a new one.
A switch is connected to it and the Solar Panel monitor is connected to the switch.
Another computer to monitor the Air Conditioning will be added to the switch.

To get the DAP setup, it is moved to my desk next to the wireless router.   When connected with an ethernet cable, all looks good.  The ip address of 192.168.1.235 is shown in the DAP setup display.  After setup is complete, remove the ethernet cable and the DAP will not respond to a ping.

With the ethernet cable connected, logged on and clicked Check for New Firmware. The response is: This firmware is the latest version.
The version is 2.06, Mon 24 Dec 2018

I can find a button to insert an image, but only a path, not upload.  Is there a way to upload an image?
« Last Edit: June 01, 2021, 10:01:21 AM by bkelly13 »
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Replaced router, no longer working
« Reply #3 on: June 01, 2021, 09:53:07 AM »

What is the IP address for the DAP seen on the host routers connected clients table?
What IP address string does your host router use? 192.168.#.something?
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

bkelly13

  • Level 1 Member
  • *
  • Posts: 4
Re: Replaced router, no longer working
« Reply #4 on: June 01, 2021, 10:03:41 AM »

I don't know how to find those things.  With the ethernet cable installed the IPV4 Network shows 192.168.1.235.  I use that to log in to the DAP via the browser.
Looking at the router manual now.
In the Synology router Network center it shown my main computer hardwired, my iphone, and dlinkap.  The MAC and the IP addresses match what I got from the D-Link.  It shows the connection as wired.  But when I disconnect the cable I cannot log in.  When put in the garage, the solar panel monitor does not update its data.

I have the ethernet cable connected.  I will disconnect it now and monitor this stuff for possible changes.


« Last Edit: June 01, 2021, 10:16:12 AM by bkelly13 »
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Replaced router, DAP-1665 no longer working
« Reply #5 on: June 01, 2021, 10:37:38 AM »

If you have the wireless client mode set on the DAP, then the ethernet cable between the DAP and router should be disconnected. The DAP is working in wireless bridge kind of mode so it should connect to the host routers wifi.

Then you should be able to connect a ethernet cable and PC to the back of the DAP and it should get internet services thru the DAP from the host router. If this worked with the prior router before and now doesn't with the newer router, I'd review the newer routers configuration and settings as well. Contact the mfr of this router for additional help and information regarding there product.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

bkelly13

  • Level 1 Member
  • *
  • Posts: 4
Re: Replaced router, DAP-1665 no longer working
« Reply #6 on: June 01, 2021, 10:50:51 AM »

Re: If you have the wireless client mode set on the DAP, ...
Seems to me that the DAP is always a wireless client mode.  That is its sole purpose.
I don't find anything to set that.
I did find some other stuff on the Synopsis router.  It has a search function that does not find anything wireless.
I will go to the Synopsis pages / forums and try there.
Thank you for your time and patience.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Replaced router, DAP-1665 no longer working
« Reply #7 on: June 01, 2021, 11:30:18 AM »

Hopefully they can help out as well.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.