• March 19, 2024, 12:19:15 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Emergency Flashing HOW-TO  (Read 474803 times)

s196635

  • Level 1 Member
  • *
  • Posts: 2
Emergency Flashing HOW-TO
« on: December 28, 2011, 08:16:07 AM »

1.  Plug the Ethernet cable that connects your computer, that was plugged into one of the LAN ports,
2. Setup your PC with static IP - ex: 192.168.0.2 (different from 192.168.0.1)
3. Make sure the PC has the new firmware
4. Unplug the power
5. Hold the reset button for 3~5 seconds and re plug the power WITHOUT RELEASING THE RESET BUTTON.
6.Open a web browser to 192.168.0.1 and then you should see EMERGENCY FLASHING page then click browse/upload locate the file and click UPLOAD FIRMWARE NOW

7. You should see a SUCCSESS page, If you don’t then re do steps 2-6
Matthew Hudson © 2010 All Rights Reserved   
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Emergency Flashing HOW-TO
« Reply #1 on: December 28, 2011, 09:06:13 AM »

S, What products does this work on? ALL? Just curious. Would be great if it worked on all. Any info would be helpful.

1.  Plug the Ethernet cable that connects your computer, that was plugged into one of the LAN ports,
2. Setup your PC with static IP - ex: 192.168.0.2 (different from 192.168.0.1)
3. Make sure the PC has the new firmware
4. Unplug the power
5. Hold the reset button for 3~5 seconds and re plug the power WITHOUT RELEASING THE RESET BUTTON.
6.Open a web browser to 192.168.0.1 and then you should see EMERGENCY FLASHING page then click browse/upload locate the file and click UPLOAD FIRMWARE NOW

7. You should see a SUCCSESS page, If you don’t then re do steps 2-6
Matthew Hudson © 2010 All Rights Reserved   

Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Emergency Flashing HOW-TO
« Reply #2 on: December 28, 2011, 09:59:11 AM »

Just tested this out on a DIR-655 and 657 and it works. Doesn't work on a DGL-4500 so I presume the DGL series of routers wont work for this process. Looks like the DIR series is good though.

One thing however, he failed to mention, you need to hold the reset button in until the amber power light keeps blinking on and off. Then you can let go and the proceed to the browser.
« Last Edit: December 28, 2011, 10:01:25 AM by FurryNutz »
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

s196635

  • Level 1 Member
  • *
  • Posts: 2
Re: Emergency Flashing HOW-TO
« Reply #3 on: December 28, 2011, 11:26:00 AM »

Works on most
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Emergency Flashing HOW-TO
« Reply #4 on: December 28, 2011, 11:38:44 AM »

Ok, will probably post this in the DIR series of routers for others to use in case of that happening. Thanks for the info.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Emergency Flashing (RECOVERY MODE) HOW-TO (UPDATED)
« Reply #5 on: January 04, 2012, 09:58:55 AM »

DIR Router - Router Recovery from Corrupt Firmware
For those of you who's routers may not start correctly due to a possible interruption during the FW update or the router has become bricked, try this:

Note: Use this is only if a Factory Reset using the button in back fails to bring the router to a ready state. There are no guarantees Recovery mode will fix anything. This is a last resort option. This procedure provides the steps necessary to recover a DIR series router that will not properly boot due to corrupt or improperly loaded firmware. Do not perform this procedure if you can successfully access the router web interface.

PC 3rd Party Security Software Configurations
  • Turn off all anti virus and firewall programs on PC and browser add-ons while using this procedure. These may interfere with the FW update process.
  • Turn off all devices accept for one wired LAN PC while testing. Disconnect the router from the main ISP modem/Services.


Use the following browsers only: IE or Fire Fox. Chrome and other browsers may cause the FW download to become corrupt or may improperly handle the data causing the router to be come bricked. Internet Explorer works sometimes however users have reported that FF has better results and works 100% of the time. For IE,  lower the IE security settings, add the 192.168.0.1 or .50 to the trusted sites under "sites" in security tab of the Internet Options.

Procedure for DIR series routers

  • Store a copy of the router firmware (.BIN) on the HDD of a local PC. Download the FW file ahead of time.
  • Connect an Ethernet cable between one of the LAN ports on the rear of the router and the network port on the local PC
  • Configure the PC with a static IP address other than 192.168.0.1 (e.g. 192.168.0.5)
  • Power down the router and unplug the power cord
  • Press and hold the reset button on the rear of the router for 3 to 5 seconds and re-plug the power cord without releasing the reset button
  • Continue to hold the reset button until the amber power light keeps blinking on and off. NOTE: For some DIR series, continue holding the reset button up to 10 seconds.
  • Open a web browser and enter the following address: http://192.168.0.1/
  • Wait for the D-Link Router Recovery Mode page to load (See Exhibit 1 below)
  • Using the Choose File button, select the router firmware stored on the local PC and then press Upload
  • After the firmware successfully loads, a Success page will display
  • If the Success page fails to display, then repeat steps 3 through 9

Exhibit 1 - D-Link Router Recovery Mode Page

Procedure for DSL series Modems
You'll need to set up a Static IP address on the wired connected PC, set to 192.168.1.49.
Store a copy of the Modem firmware (.IMG) on the HDD of a local PC
- Switch Modem OFF.
- Press the reset button, i.e. insert ballpoint pen in reset hole under the Modem.
- Keep holding the reset button and turn ON the Modem.
- Keep holding the reset button for about 12 seconds after you power ON the Modem.
- Now you'll see that the power led has turned RED signifying that the Modem is in crash recovery mode.
- When you enter the address 192.168.1.1 on your PC browser, you find the upgrade firmware page.
- Just browse to the downloaded firmware file and flash!

D-Link products confirmed and tested for the Recovery Mode: DIR-890L, DGL-5500, DIR-868L, DIR-615, DIR-655 (Rev B and C), DIR-657, DIR-825, DIR-685, DIR-601, DAP-1360, DIR-826L, DAP-1350, DSL-2750B and 2750U.
Presume most if not all DIR series routers support this mode. Will add models if anyone can confirm other models not already posted.

For DIR-645 series routers, please try the following IP address:
192.168.0.101
http://forums.dlink.com/index.php?topic=58080.0
NOTE: 20161107 SIERRA OSX USERS
"I just joined the forum after trying to unbrick my DIR-645 using the Emergency Room tips here. I wasn't able to fix it using the techniques described here, so I went investigating a bit, and came up with a hypothesis on why it didn't work for me, as well as a browser-independent solution (which is a bit technical). From what I can deduce after packet sniffing the conversation between the router and my computer, the browsers I tested (FF, Safari, Chrome) try to upload the firmware image with a content-type of "application/macbinary" instead of "application/octet-stream"  on OS X, which could be why it didn't work for me (and seeing as the latest DIR-645 advice is from 2012, they may have changed their behaviour).

Anyway, I managed to upload the firmware using curl (http://curl.haxx.se/) using a command line of

curl -X POST -v -i -F "firmware=@DIR645A1_FW106B01.bin" http://192.168.0.101/

and got the router to reboot into the normal GUI at 192.168.0.1. Just thought I'd share it in case anyone else on OS X has had problems with it recently.

For DIR-506L series routers, please try the following IP address:
192.168.123.254
http://forums.dlink.com/index.php?topic=55175.0

For COVR series extender Points:
Connect to your computer via Ethernet to the remote Point, statically assign your computer 192.168.0.2 / 255.255.255.0
Paper clip the reset button on the bottom, power on while holding the reset button, wait till front COVR led blink RED then release the button.
Go to 192.168.0.50 in a web browser.

DAP model APs:
192.168.0.50
Confirmed working on a DAP-1665

D-Link products tested for the Recovery Mode that do not support this mode: DGL-4500 and presume all DGL Series routers. The DGL-5500 is the only model that supports recovery mode. DIR-865L. Any other products found to support or not support this option, send me a PM and I'll add it to the list. Older generation routers like the DIR-655/825/855 Rev A series do not support recovery mode.

If this recovery process fails to correct the routers condition, it's recommended to contact D-Link support and seek an RMA for your router.

DCS Series Cameras:
Disconnect Power
    Press and hold "Reset", connect Power and hold Reset until the blue LED goes out (about 8 seconds).
    Release reset
    Configure your computer to 192.168.0.x
    Fire up a web browser and connect to 192.168.0.20
    Upload your new firmware in the emergency web interface
http://www.dlink.com/uk/en/support/faq/cameras-and-surveillance/dcs-series/dcs_recovery_procedures_after_bad_flash_firmware

DCS-5222L Ax Bx - DCS-2332L - DCS-2132L Ax Bx - DCS-2310L - DCS-6010L - DCS-7010L - DCS-2136L - DCS-2330L - DCS-2332L
1. Plug a microSD card to your computer. Format it in FAT32. Once formatted, create a folder called "upgrade".
2. Download the latest firmware from support.dlink.com. Unzip and rename the file update.bin. Then copy to the upgrade folder on the microSD card.
3. Turn off the camera (remove the power cord) and insert the microSD into the slot provided.
4. Press and hold the reset button (for example use a paper-clip)
5. Plug the power cord into the device whilst holding down the reset button for about 3 seconds, until the red LED starts flashing. Immediately release the reset button.
6. Wait 140-160 seconds until the camera completes the process of recovery of the firmware without removing the power cord.
7. At the end of the process the LED will stop flashing and turn green.
8. At this point, remove the power cord and remove the MicroSD card.

DCS-960L
1. Hold in reset button, unplug power and plug back in while holding it for 10 seconds.
2. Wait about a minute. This will automatically enter "rescueCam" mode.
3. Please a client to find SSID: rescue-Cam-XXXX (xxxx=last 4 digits of the camera's MAC address). You need to statically assign your wireless adapter a static IP of 192.168.1.xxx / 255.255.255.0 (anything but 30)
4. Open browser and go to http://192.168.1.30. Install the 1.04 or 1.06 firmware.
5. Once done, run the setup wizard or app to reinstall the camera.
You can ignore the app's request to upgrade and do it manually through the web gui of the camera.

Additional Resource:
Of Modems and Men - Unbricking Tutorial
« Last Edit: December 20, 2018, 11:49:29 AM by FurryNutz »
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.