D-Link Forums

The Graveyard - Products No Longer Supported => Routers / COVR => DIR-850L => Topic started by: Alko on September 29, 2015, 11:41:30 PM

Title: Internet conection
Post by: Alko on September 29, 2015, 11:41:30 PM

DIR-850L Firmware Version : 1.10WW Hardware Version : A1

So I have 2 LTs both conected to router with wireless one have internect acses ather not need help to solve it I use DHCP conection tipe.
tryed few times reset relog restart clear logs nothing helps conect ather LT to internet

Title: Re: Internet conection
Post by: FurryNutz on September 30, 2015, 07:56:43 AM

Link>Welcome! (http://forums.dlink.com/index.php?topic=48135.0)

• What Hardware version is your router? Look at sticker under the router case.
• Link>What Firmware (http://forums.dlink.com/index.php?topic=47512.0) version is currently loaded? Found on the routers web page under status.
• What region are you located?
• Are you wired or wireless connected to the router?
• Has a Factory Reset (http://blog.dlink.com/what-is-a-reset-button-when-should-i-use-it) been performed?
• Was a Factory Reset performed before and after any firmware updates then set up from scratch?

  Link> >FW Update Process (http://forums.dlink.com/index.php?topic=42457.0)

• Was the router working before any firmware updates?

Internet Service Provider and Modem Configurations

• What ISP Service do you have? Cable or DSL?
• What ISP Modem Mfr. and model # do you have?

Router and Wired Configurations
Some things to try: - Log into the routers web page at 192.168.0.1. Use IE, Opera or FF to manage the router. Besure to log into the Admin account on the router.

• Setup DHCP (http://forums.dlink.com/index.php?topic=58017.0) reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting and maintain consistency for applications that need to connect as well as mapped drives.
• Ensure devices are set to auto obtain an IP address.
• If IPv6 (http://en.wikipedia.org/wiki/Ipv6) is an option on the router, select Local Connection Only under Setup/IPv6.
• Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall. Enable or Disable SPI (http://en.wikipedia.org/wiki/SPI) to test.
• Enable uPnP (http://en.wikipedia.org/wiki/Upnp) and Multi-cast Streaming (http://en.wikipedia.org/wiki/Multicast) under Advanced/Networking. Disable uPnP for testing Port Forwarding (http://forums.dlink.com/index.php?topic=4235.0) rules. Enable IPv6 Multi-cast Streaming for routers that have a Media Server option. Disable IPv6 Multi-cast Streaming if IPv6 or Media Server is not being used.

Wireless Configurations
Links>Wireless Installation Considerations (http://forums.dlink.com/index.php?topic=48327.0) and Managing Signal Congestion (http://forums.dlink.com/index.php?topic=53228.0) and Good Neighbour Policy (http://forums.dlink.com/index.php?topic=10634.0)

• Ensure the default (dlink) SSID name is changed. Ensure that different SSID names are used between each WiFi 2.4/5Ghz radios. Can be anything and not something that's already in use by any neighbouring WiFi routers. Under Setup/Wireless/Manual.
• What wireless modes are you using?
• 2.4Ghz and 5Ghz routers: Try single mode G or N or mixed G and N on 2.4Ghz and single mode N or AC on 5Ghz?
• Channel Width set for Auto 20/40Mhz
• Try setting a manual Channel (http://en.wikipedia.org/wiki/Wireless_channels) to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear. 13 for EU regions. Try channel 48 or 149 on 5Ghz.
• What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES (http://en.wikipedia.org/wiki/Advanced_Encryption_Standard), so you might want to try TPIK (http://en.wikipedia.org/wiki/Temporal_Key_Integrity_Protocol) only or Auto TPIK and AES.
• What wireless devices do you have connected?
• Ensure any devices with WiFi adapter drivers are updated.
• If you have any of these options, Try turning OFF or ON Short GI (http://www.smallnetbuilder.com/wireless/wireless-features/30969-what-do-80211ns-optional-features-mean-for-you), WLAN Partition, Extra Wireless Protection and HT 20/40 Co-existence if you have it. Also testing with HT20/40Mhz Co-existence enabled will impact results as well. I prefer to use this option OFF. Recommended settings are default. Under Advanced/Advanced Wireless.