Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[FurryNutz]

I do, it's a NA unit using NA FW, v2.07 so not sure if loading your config file would work. Worth a try though if you want me to.

I've asked one of our resident IPv6 experts to review this to see if there could be an issue.

So if you configure the router for everything, accept IPv6 tunnel broker, save the config to file, can you access the pages? Trying to help you narrow this down as much as possible.

[Cornholio]

I Can use IPv6, because its a ipv6 through ipv4 tunnel.

[FurryNutz]

Since these units are probably similar in HW, I could load your version of FW and then load your config file too.  

[FurryNutz]

Let see if our forum experts can chime in on this. Possible issue with the configuration or configuration mixed with FW not working with the configuration correctly.

[Cornholio]

current config:
http://demeij.net/config/config_with_ipv6.bin

btw, Tried turning off IPv6 (put on link-local only), now still cannot open pages anymore.
Latest firefox sends me back to loginscreen instead of opening status pages.

'main' status screen (Device info) works fine, the rest looks broken.

[FurryNutz]

Only thing I would do is this:
Downgrade to v2.05EUB09 Firmware 06/01/2012 to see if the problem follows. I don't see any release notes on v2.06WW nor is it released on the UK site and the NL site displayed a back link error when I attempt to look up the 825 for your area.

Where did you get v2.06WW from?

If you do attempt to downgrade, factory reset first, send the file, factory reset ONCE more, then use IE or FF to set up the router from scratch and see if the problem appears. DO Not load the saved configuration file.

I'll have a look at the config file you linked and see if I notice anything. I won't actually be able to test this until later this evening after work.

[FurryNutz]

Looking at your config file, one thing to test would be to disable SPI and set NAT to Endpoint Independent for both TCP and UDP and see. I don't think this should effect anything however since you are tunneling with IPv4, might be worth a test. 

[Cornholio]

Just did a 'check for updates' on the router itself, and got the link from that page.....

Where can I get the v2.05EUB09 version ?

did you already downloaded the config ? because my webserver is running behind the router
(factory reset breaks it)

testing later this evening ? no problem at all !!
my internet is working fine, so no hurries

[Cornholio]

Looking at your config file, one thing to test would be to disable SPI and set NAT to Endpoint Independent for both TCP and UDP and see. I don't think this should effect anything however since you are tunneling with IPv4, might be worth a test. 

nope, doesnt work

[FurryNutz]

Just did a 'check for updates' on the router itself, and got the link from that page.....

Where can I get the v2.05EUB09 version ?
http://www.dlink.com/uk/en/support/product/dir-825-xtreme-n-dual-band-gigabit-router
The v2.06WW was never posted officially to the UK or any other site that I can find. Not sure why or why it was pushed to routers and not made it official on the web sites. 

did you already downloaded the config ? because my webserver is running behind the router
(factory reset breaks it)
Yes I go the file.

testing later this evening ? no problem at all !!
my internet is working fine, so no hurries

Let us know what the results are if you try v2.05EU

[Cornholio]

going to downgrade as described above !

brb

[Cornholio]

Ok, Back online.

done all the config except the IPv6, status pages are working fine for now.
saved config, going to configure my tunnel now.

[Cornholio]

and its broken again

[FurryNutz]

ok so something break when you go to configure IPv6 tunnel. Lets see if our other resident IPv6 guru's can offer up some help here. At least we know it's in 2 different versions of FW. I'm thinking it could be a configuration issue. 

[Cornholio]

keeps me wondering why it did work for a long time.
btw, tunnel itself is working fine, I just can't open status pages