Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

Hey everyone, I'm looking for some assistance on loading my pldt home wifi using GCash. I've heard it's a convenient method, but I'm unsure about the steps involved. Could someone kindly share a step-by-step guide or any insights on the process? Are there specific details I need to be mindful of during the transaction? Your experiences or advice would be greatly appreciated. I'm eager to streamline the process and make the most of this digital payment method. Thanks in advance for your help!

I'm trying to connect the camera to an ANNKE NVR using the ONVIF protocol.

I have successfully set up the camera with the mydlink app (which works fine). I have tested it with ONVIF Device Manager to which it connects ok.
I have successfully connected other older dlink cameras to the NVR (DCS-2230L & DCS-2132LB1) which work ok
I'm using the camera IP address of Restaurant Menus, user admin and password is the 6 digit PIN on the bottom of the camera.
The NVR identifies the 8300LHV2 online as an ONVIF device. When added it tries to connect, after a few seconds the LED on the front of the Camera turns from green to red and the NVR reports ‘IP Camera Exception'
I've tried numerous times to make it connect but it’s just not working. Can anyone suggest what I'm doing wrong? I thought ONVIF was supposed to make these connections simple.
Thank you.

It seems like you've taken the necessary steps to set up the camera with ONVIF, but you're facing issues with the NVR connection. To troubleshoot:

Confirm camera compatibility with ONVIF.
Check and update firmware on both camera and NVR.
Verify port configuration and network settings.
Ensure correct authentication details.
Temporarily disable firewall/antivirus.
Examine camera logs for error messages.
Contact technical support for both camera and NVR.
These steps should help identify and resolve the connection issue.

Added as help for others

Enabled SMB1 support
WIN+R  run optionalfeatures
enable SMB1.0/CIFS File Sharing Support
NAS would not MAP
I could use CMD  Net use Y : \\MachineName\ShareName
it would complete successfully but drives still not show

As workaround used WIN+E and entered \\IP-address\shared-folder
This would create shortcuts on 'My Computer' so I could access data

Final fix in my case - I have MalwareBytes installed, I contacted Malwarebytes ... they provided data gather tool, analyzed results sent me FRSTfis tool and a very very long set of customised scripts, that the tool run automatically.

It run - took about an Hr, but as soon as finished Mapped Drives appeared.

Hello forum members,

I hope this message finds you well. I'm currently in the process of reapplying for the SASSA R350 grant, and I wanted to reach out to the community for any advice or insights you may have. As the application landscape can sometimes be intricate, your experiences and suggestions could be immensely valuable.

Specifically, I'm interested in hearing about the reapplication process, any changes or updates in the requirements, and tips to ensure a smooth application. If anyone has successfully navigated this process or has relevant information on sassa reapplication for r350, please share your thoughts. Additionally, if there are any common pitfalls or challenges that one should be aware of, your input would be greatly appreciated.

Thank you all in advance for your time and assistance. Your collective wisdom can make a significant difference in ensuring a successful SASSA reapplication experience.

Hi,

 

I've tried to create my own workflow for calculating VAT and showing it in dynamically, but I can't work it out. Can someone do this for me so I can understand how it's done? .

Basicallty I was trying to use PHP to a calculation on southafricanvatcalculator.co.za, if I typed in for example 500 it would show the result of 500 / 1.2 * 0.2 and give me how much VAT would be. I do this so I know how much VAT to put to one side on every transaction but it's annoying to keep typing out the full equation every time when of course, this is what Alfred is built for! Productivity!

 

If anybody could help I'd be so thankful.

Dedicated offshore developers have evolved into a strategic resource for businesses aiming to navigate the complexities of modern software development. By leveraging global talent, achieving cost efficiency, and embracing scalable solutions, companies can position themselves for growth, innovation, and sustained success in the dynamic digital landscape. As the trend toward offshore development continues, businesses stand to gain a competitive edge by adopting this strategic approach to their development initiatives.
https://mlsdev.com/services/it-staff-augmentation

I assume Network file discovery is enabled?
I just had to set my IP address to match the default for the 323 as 192.168.0.xx and had to enable network discovery again.
Might be worth disabling and enabling again?

See if this helps at all. https://serverfault.com/questions/1021222/mapped-network-drive-with-smb1-and-windows-10

Using IP Advanced scanner, I can compare one gainst the other.
The 101 is not showing any http interface, whilst the 102 is?
Also as can be seen the 101 is showing as Expressif Inc as manufacturer, where as before it would show the same as 102.. Dlink

Unable to see how to add an attachment or paste an image? 

Greetings all.
Not a great start to my Xmas. 

I have two DNS323 units, both running ffp.
I had a power loss and the found out that I could not connect to the oldest one.
I have switched it off an on numerous times. I have even tried the reset button.
I have tried connecting a PC to it directly and hardcoding an IP address on 19.168.0.xx on the PC.
The EasySearch utility was worse than useless. It did not even find the second DNS323 ? 

The unit is retaining it's 192.168.2.101 ip address.

After a good deal of playing around, I have found that my mapping works again. Phew, that is a relief. :-)

However I am unable to connect to it via the ip address, or via telnet.
In a browser I get '192.168.2.101 refused to connect'.
In the command window and telnet I get 'Connecting To 192.168.2.101...Could not open connection to the host, on port 23: Connect failed'

At the moment I still have my data, and I can always remove the disks if need be, BUT does anyone have any ideas as to how I can get back into it please?

I have no idea why it managed to keep it's IP address when I used the reset hole several times as a last resort.
It also holds all my music for streaming around the house.

I also have another hard drive hanging off the USB port for Downloads. I was able to access that data now and again, when not able to access Volume_1 ?

TBH it has been a few years since I even played around with either unit. I set them up, and left them to it. They have behaved flawlessly over the years. This is my first hiccup with one of them, other than a hard disk failure a good few years back.

Any and all ideas welcome please.

Went to use 323 and the drives are no longer mapped.
Enabled SMB1.0 protocol support.
 Using the D-Link supplied 'Easy Search utility'   as per CD-ROM provided with the DNS-323, unbale to map drive
Easy Search utility does find DNS-323 but 'map drive' does not work

https://flic.kr/p/2pnmRVC


Previously advised Easy Search no longer works, so  Mapped drive from Command screen using:
Net use Y: \\MachineName\ShareName

in my case syntax was   

C:\>Net use Y: \\DLINK-EAB58D\Volume_1

It was successful and both Y & Z drives show if I use CMD  and net use
But nothing showing up in 'My computer' / Windows Explorer.

Can anyone suggest a way forward?