The Graveyard - Products No Longer Supported > DIR-878
DIR-878 Firmware v1.12B01 Released
FurryNutz:
Will do.
--- Quote from: GreenBay42 on March 08, 2019, 07:47:55 AM ---Kewl. Yeah open remote management. I would enable HTTPS and put in a custom port. PM me your IP, username and pw, and port.
--- End quote ---
FurryNutz:
Ok, so I can't seem to reproduce the NAT issue with v1.12.
This time I first did a factory reset, loaded v1.12 on top of v1.10, factory reset once more, then setup from scratch. Now both game consoles are OPEN NAT at the networking dashboard. ;D
I hard powered them both off and swapped which one was turned on first. OPEN NAT for both still. ::)
I believe last time I didn't start out with a reset, I think I applied v1.12 on top of v1.10 then continued. I thought at one point I did do a factory reset after v1.12 was applied as well. Or possibly the change in cable modems since last time I had the 878 online may have been a factor as well, however I doubt it.
Even if I did a factory reset upon last v1.12 load and setup from scratch, any FW issues should have been cleared out. I also believe that loading v1.12 over v1.10 and not doing a reset may have given false results, however, v1.10 has worked for both game consoles getting OPEN NAT, and applying v1.12 over v1.10 and continuing with out a reset caused one console to get Moderate NAT, then I would think there is some forum of a application issue with updating to v1.12 over v1.10 which seems to cause one game console to not get OPEN NAT on v1.12 when both did on v1.10. :-\
I'll run this this week with both consoles and see how things go. I'll probably recommend that if users are using this model router and have two game consoles, factory reset, load v1.12, then do one more factory reset and setup from scratch. This would keep the system and uPnP in working order for multiple game consoles. My 878 is slated to go to Bro In Law house and he's getting ready to setup internet this week so I'll probably not be able to test with this model again.
HOWEVER, I have found another bug in v1.12 I believe with the wifi button in back which i'll post about in a new post. ::)
twisted_mind:
If i can add :
I did the factory reset > load 1.12 >> factory reset right before i created my thread.
Two consoles both hardwired to the 878. One PS4 Pro and other Xbox One X. The PS4 sticks to NAT Type 2 in settings and Open within games. But the Xbox 1X loses open nat and goes to moderate or strict overnight when left in Instant On mode.
Tried energy saving mode on the 1X and it gets open nat the next day on bootup but then the PS4 loses it's open NAT. No portforwarding whatsover done. Let me know if you guys need any further info although furry should have most of my details
FurryNutz:
Both of my xbox ones have Instant ON disabled. I didn't test with it ON since i know of the erratic behaviors it can cause like this. I'll check on the console NAT this evening and see if anything has changed. I did do a hard reset on both consoles after turning them and on checking NAT then holding the power button until they turned off. Clears any caches out of there system.
NAT Type 2 is what is expected for PS with a router in the mix.
Possible for you to factory reset > load 1.12 >> factory reset and test again to see if your still experiencing the same problem with both of your consoles? May ask you to setup remote management and let someone at D-Link review your router settings. Also please do a save router config to file and we'll have you send it to someone at D-Link for review as well.
I'll check mine again tonight and see if anything has changed since Sunday nite.
When you say "next day on bootup but then the PS4 loses it's open NAT", is this on the PS networking dashboard or in game? If in game, what game is it that you see this?
Navigation
[0] Message Index
[*] Previous page
Go to full version