• April 18, 2024, 06:37:07 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Motion Detection - DCS-920  (Read 7727 times)

drewtj

  • Level 1 Member
  • *
  • Posts: 6
Motion Detection - DCS-920
« on: October 28, 2009, 04:00:52 PM »
It seems my DCS-920 is constantly seeing motion when no motion exists! I have the sensitivity down to 5% and the percentage at 5% (though I don't know what percentage is for).

My problem is that I record the video when motion is detected, and want it to record for 30 seconds and then stop. With it being constantly protected, I'm eating up disk space unnecessarily.

Help!

I am using the latest firmware version and the latest version of dviewcam.
« Last Edit: October 28, 2009, 04:11:16 PM by drewtj »
Logged

ECF

  • Administrator
  • Level 11 Member
  • *
  • Posts: 2692
Re: Motion Detection - DCS-920
« Reply #1 on: October 28, 2009, 04:12:16 PM »
What version of D-ViewCam are you running? Also what size area are you covering for a motion detection area of the picture?
Logged
Never forget that only dead fish swim with the stream

drewtj

  • Level 1 Member
  • *
  • Posts: 6
Re: Motion Detection - DCS-920
« Reply #2 on: October 28, 2009, 04:16:00 PM »
Version 2.03. I have two squares covered (if I'm doing it right). When I mouse over the image, a square with an X is displayed. I'm assuming that those squares is where it will attempt motion detection.
Logged

drewtj

  • Level 1 Member
  • *
  • Posts: 6
Re: Motion Detection - DCS-920
« Reply #3 on: November 09, 2009, 12:30:11 PM »
Can I get some support here, otherwise this camera is useless.
Logged

ECF

  • Administrator
  • Level 11 Member
  • *
  • Posts: 2692
Re: Motion Detection - DCS-920
« Reply #4 on: November 09, 2009, 02:53:19 PM »
Try filling the whole screen and set the percentage to about 80 and sensitivity to 10 percent.
Logged
Never forget that only dead fish swim with the stream

drewtj

  • Level 1 Member
  • *
  • Posts: 6
Re: Motion Detection - DCS-920
« Reply #5 on: November 10, 2009, 09:57:28 AM »
No luck, it's still just constantly recording. I have the schedule set to 24/7 Economic Recording.
Logged

ECF

  • Administrator
  • Level 11 Member
  • *
  • Posts: 2692
Re: Motion Detection - DCS-920
« Reply #6 on: November 10, 2009, 11:35:26 AM »
Please try disabling recording and try event recording on motion detection.
Logged
Never forget that only dead fish swim with the stream

drewtj

  • Level 1 Member
  • *
  • Posts: 6
Re: Motion Detection - DCS-920
« Reply #7 on: November 12, 2009, 08:49:51 AM »
Ok, I've done that. Set the entire window as the detection area, set the sensitivity to 10% and frequency to 80%. I've enabled record on the motion detection event only (and turned off the scheduled one).

It's still recording constantly. Anything else I can try?
Logged

ECF

  • Administrator
  • Level 11 Member
  • *
  • Posts: 2692
Re: Motion Detection - DCS-920
« Reply #8 on: November 12, 2009, 09:14:34 AM »
Have you tried it on another PC or tried uninstalling and reinstalling the software, the software seems to glitching. Also there is a 2.04 version of the software if you search under the DCS-1100 or 1130 on the support site you may want to try out.
Logged
Never forget that only dead fish swim with the stream

drewtj

  • Level 1 Member
  • *
  • Posts: 6
Re: Motion Detection - DCS-920
« Reply #9 on: November 12, 2009, 09:15:53 AM »
I uninstalled and reinstalled and now it's working. Strange. Thanks for the tip.
Logged