• April 16, 2024, 09:23:06 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Firmware update failure  (Read 24203 times)

tjdp

  • Level 1 Member
  • *
  • Posts: 3
Firmware update failure
« on: May 21, 2010, 09:46:43 PM »
I tried to update my DIR-825 router to the 203NA firmware and it got interrupted midway.  Now I can't connect to the router using the default ip address (and by extension reinstall the firmware).  Any ideas how I can fix my issue?
Logged

Athan

  • Level 1 Member
  • *
  • Posts: 16
Re: Firmware update failure
« Reply #1 on: May 22, 2010, 03:21:42 AM »
Try hard resetting router using the 30-30-30 procedure:

1. Power on the router

2. Hold the reset on the back for 30 seconds, until orange led start blinking.

3. While still holding the reset button, remove the power plug and keep pressing reset for another 30 seconds.

4. While still holding the reset plug in the power connector and keep pressing reset for another 30 seconds.

5. Release the reset button and after a few seconds connect to router's default IP (192.168.0.1) with your browser. Don't use browsers other than Internet Explorer, they won't work.

6. In bootload form select the right firmware binary and send it to router. When finished (100%), wait a few seconds and repeat resetting steps 2-4

7. Finally unplug the power connector (without pressing reset), wait for another 30 seconds and power on the router.

I hope it helps!  :)
Logged
Please excuse my poor English. I'm not a native English speaker.

tjdp

  • Level 1 Member
  • *
  • Posts: 3
Re: Firmware update failure
« Reply #2 on: May 22, 2010, 08:03:01 AM »
I've tried the 90 sec reset (With power cycling) but connecting in internet explorer still doesn't work (cannot display webpage).  I'll try again a few more times later.
Logged

Athan

  • Level 1 Member
  • *
  • Posts: 16
Re: Firmware update failure
« Reply #3 on: May 22, 2010, 08:17:29 AM »
What's your computer's IP address?
Don't use automatic settings (DHCP). Give your system a static IP in 192.168.0.xxx range (see the following example) and try once again the 30-30-30 resetting procedure.

IPv4 settings example (Windows):

IP address: 192.168.0.100
Subnet mask: 255.255.255.0
Default gateway: 192.168.0.1
Preferred DNS server: 192.168.0.1
« Last Edit: May 22, 2010, 08:21:25 AM by Athan »
Logged
Please excuse my poor English. I'm not a native English speaker.

tjdp

  • Level 1 Member
  • *
  • Posts: 3
Re: Firmware update failure
« Reply #4 on: May 22, 2010, 10:38:26 AM »
Thanks.  That fixed it.
Logged

Steve Al-Mousa

  • Level 1 Member
  • *
  • Posts: 1
Re: Firmware update failure
« Reply #5 on: December 27, 2020, 03:18:29 AM »
Hi, I've upgraded the firmware for the DIR 825 G1 and can't access it by all ways after rebooted. i only get the power and lan led blue lights.
tried your method but there's no orange light


Quote from: Athan on May 22, 2010, 03:21:42 AM
Try hard resetting router using the 30-30-30 procedure:

1. Power on the router

2. Hold the reset on the back for 30 seconds, until orange led start blinking.

3. While still holding the reset button, remove the power plug and keep pressing reset for another 30 seconds.

4. While still holding the reset plug in the power connector and keep pressing reset for another 30 seconds.

5. Release the reset button and after a few seconds connect to router's default IP (192.168.0.1) with your browser. Don't use browsers other than Internet Explorer, they won't work.

6. In bootload form select the right firmware binary and send it to router. When finished (100%), wait a few seconds and repeat resetting steps 2-4

7. Finally unplug the power connector (without pressing reset), wait for another 30 seconds and power on the router.

I hope it helps!  :)
Logged